ABB DCS550 Series, Manual

Page: 215 / 316

215
Signal and parameter list
3ADW000379R0501 DCS550 Manual e e
Signal / Parameter name
m
in.
ma
x.
def
.
uni
t
26.05 TorqMux (torque multiplexer)
TorqMux (26.05) selects a binary input to change between operation modes. The choice of the operation
modes is provided by means of TorqMuxMode (26.04). Torque reference multiplexer binary input:
0 = NotUsed
operation mode depends on TorqSel (26.01), default
1 = DI1 0 = speed control, 1 = depends on TorqMuxMode (26.04)
2 = DI2 0 = speed control, 1 = depends on TorqMuxMode (26.04)
3 = DI3 0 = speed control, 1 = depends on TorqMuxMode (26.04)
4 = DI4 0 = speed control, 1 = depends on TorqMuxMode (26.04)
5 = DI5 0 = speed control, 1 = depends on TorqMuxMode (26.04)
6 = DI6 0 = speed control, 1 = depends on TorqMuxMode (26.04)
7 = DI7 0 = speed control, 1 = depends on TorqMuxMode (26.04)
8 = DI8 0 = speed control, 1 = depends on TorqMuxMode (26.04)
9 = DI9 0 = speed control, 1 = depends on TorqMuxMode (26.04), only available with digital
extension board
10= DI10 0 = speed control, 1 = depends on TorqMuxMode (26.04), only available with digital
extension board
11 = DI11 0 = speed control, 1 = depends on TorqMuxMode (26.04), only available with digital
extension board
12 = MCW Bit11 0 = speed control, 1 = depends on TorqMuxMode (26.04), MainCtrlWord (7.01) bit 11
13 = MCW Bit12 0 = speed control, 1 = depends on TorqMuxMode (26.04), MainCtrlWord (7.01) bit 12
14 = MCW Bit13 0 = speed control, 1 = depends on TorqMuxMode (26.04), MainCtrlWord (7.01) bit 13
15 = MCW Bit14 0 = speed control, 1 = depends on TorqMuxMode (26.04), MainCtrlWord (7.01) bit 14
16 = MCW Bit15 0 = speed control, 1 = depends on TorqMuxMode (26.04), MainCtrlWord (7.01) bit 15
Int. Scaling: 1 == 1 Type: C Volatile: N
No
tUs
e
d
M
C
W
B
it
15
No
tUs
e
d
-
Group 30: Fault functions
30.01 StallTime (stall time)
The time allowed for the drive to undershoot StallSpeed (30.02) and exceed StallTorq (30.03). A triggered stall
protection leads to F531 MotorStalled [FaultWord2 (9.02) bit 14].
The stall protection is inactive, if StallTime (30.01) is set to zero.
Int. Scaling: 1 == 1 s
Type: I Volatile: N
0 200 0 s
30.02 StallSpeed (stall speed)
Actual speed limit used for stall protection.
Internally limited from:
rpm to rpm ) 29 . 2 ( 0
Int. Scaling: (2.29) Type: I Volatile: N
0 1000 5 rp
m
30.03 StallTorq (stall torque)
Actual torque limit - in percent of MotNomTorque (4.23) - used for stall protection.
Int. Scaling: 100 = 1 %
Type: I Volatile: N
0 325 75 %
30.04 - 30.07 Unused
30.08 ArmOvrVoltLev (armature overvoltage level)
The drive trips with F503 ArmOverVolt [FaultWord1 (9.01) bit 2] if ArmOvrVoltLev (30.08) - in percent of
M1NomVolt (99.02) - is exceeded. It is recommended to set ArmOvrVoltLev (30.08) at least 20 % higher than
M1NomVolt (99.02).
Example:
With M1NomVolt (99.02) = 525 V and ArmOvrVoltLev (30.08) = 120 % the drive trips with armature voltages >
630 V.
The overvoltage supervision is inactive, if ArmOvrVoltLev (30.08) is set to 328 % or higher.
Int. Scaling: 10 == 1 %
Type: I Volatile: N
20 500 120 %
30.09 ArmOvrCurLev (armature overcurrent level)
The drive trips with F502 ArmOverCur [FaultWord1 (9.01) bit 1] if ArmOvrCurLev (30.09) - in percent of
M1NomCur (99.03) - is exceeded. It is recommended to set ArmOvrCurLev (30.09) at least 25 % higher than
M1NomCur (99.03).
Example:
With M1NomCur (99.03) = 850 A and ArmOvrCurLev (30.09) = 250 % the drive trips with armature currents >
2125 A.
Int. Scaling: 10 == 1 %
Type: I Volatile: N
20 400 250 %