WAGO I/O-SYSTEM 750-666/000-003 Скачать руководство пользователя страница 163

Страница: 163 / 166

WAGO-I/O-SYSTEM 750

List of Tables 163

750-666/000-003 4FDI/2FDO 24V/10A PROFIsafe V2 iPar

Manual

Version 1.2.0, valid from HW/SW Version 01/01

List of Tables

Table 1: Number notation ...................................................................................... 11

Table 2: Font conventions ..................................................................................... 11

Table 3: iPar server legend .................................................................................... 18

Table 4: Application range .................................................................................... 21

Table 5: Legend for “View” figure ....................................................................... 22

Table 6: Caption acc. to view “Power jumper contacts” ....................................... 24

Table 7: Connections ............................................................................................. 26

Table 8: Display elements, inputs 1 ... 4 ............................................................... 27

Table 9: Display elements, outputs 1 ... 2 ............................................................. 27

Table 10: Display elements, communication / I/O module status ......................... 28

Table 11: Technical data, device ........................................................................... 32

Table 12: Technical data, supply ........................................................................... 32

Table 13: Technical data, communication ............................................................ 33

Table 14: Technical data, digital inputs ................................................................ 34

Table 15: Technical data, digital clock outputs ..................................................... 34

Table 16: Technical data, digital power outputs ................................................... 35

Table 17: Safety parameters for two-channel safety application .......................... 36

Table 18: Safety parameters for two-channel safety application .......................... 37

Table 19: Safety parameters for single-channel safety application ....................... 38

Table 20: Safety parameters for single-channel safety application ....................... 39

Table 21: Safe response time of the digital inputs in the event of failure ............. 41

Table 22: Safe response time of the digital inputs in the error-free operation ...... 42

Table 23: Response times of the digital power outputs in the event of a failure or

if there is no failure ...................................................................................... 43

Table 24: Output configurations and response thresholds of the external voltage

monitoring .................................................................................................... 65

Table 25: Maximum negative voltage of the diode recovery circuit, output

configuration H-Side/L-Side 2 ..................................................................... 87

Table 26: Adjustable parameters ......................................................................... 101

Table 27: Input pulse durations depending on the input filter time .................... 102

Table 28: Input / clock output assignment .......................................................... 103

Table 29: Error detection ..................................................................................... 104

Table 30: Antivalent evaluation .......................................................................... 108

Table 31: Equivalent evaluation .......................................................................... 108

Table 32: Necessary signal states for acknowledgement if the restart inhibit is set

to "yes" ....................................................................................................... 109

Table 33: Process image PROFIsafe V1 mode ................................................... 122

Table 34: PROFIsafe inputs, V1 mode ............................................................... 122

Table 35: PROFIsafe outputs, V1 mode, output configuration „H-Side/L-Side 2“

or „H-Side/H-Side 2“ ................................................................................. 122

Table 36: PROFIsafe outputs, V1 mode, output configuration „H-Side/L-Side 1“

or „H-Side/H-Side 1“ ................................................................................. 122

Table 37: Process image PROFIsafe V2 mode ................................................... 123

Table 38: PROFIsafe inputs, V2 mode ............................................................... 123

Table 39: PROFIsafe outputs, V2 mode, output configuration „H-Side/L-Side 2“

or „H-Side/H-Side 2“ ................................................................................. 123

Table 40: PROFIsafe outputs, V2 mode, output configuration „H-Side/L-Side 1“

or „H-Side/H-Side 1“ ................................................................................. 123

Содержание I/O-SYSTEM 750-666/000-003







































































































































































Результаты поиска

Содержание I/O-SYSTEM 750-666/000-003

Отзывы:

Похожие инструкции для I/O-SYSTEM 750-666/000-003

Бренды по названию

Популярные бренды

WAGO I/O-SYSTEM 750-666/000-003, Руководство пользователя

Результаты поиска

Содержание I/O-SYSTEM 750-666/000-003

Отзывы:

Похожие инструкции для I/O-SYSTEM 750-666/000-003

Бренды по названию

Популярные бренды