WAGO I/O-SYSTEM 750-666/000-003 Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 166

background image

56

Connect Devices

WAGO-I/O-SYSTEM 750

750-666/000-003 4FDI/2FDO 24V/10A PROFIsafe V2 iPar

Manual

Version 1.2.0, valid from HW/SW Version 01/01

6.2.1

Using 230V AC I/O Modules

If 230 VAC I/O modules are used together with PROFIsafe I/O modules in one
fieldbus node, there are two options:

6.2.2

230V AC modules are used in another fieldbus node that
contains no PROFIsafe I/O modules

You have to use a separate 24 VDC power supply unit (PELV/SELV) for a
fieldbus node that contains PROFIsafe I/O modules. You have to use a PELV or
FELV power supply unit with protective grounding for a fieldbus node without
PROFIsafe I/O modules.

Avoid unacceptably high body voltages!

All 230 V AC voltages applied to the nodes must also be protected by a 30 mA
residual current circuit breaker.

In the simplest case, place the residual current operated circuit-breaker just behind
the junction of the supply network. Doing so allows you to fuse all paths.

Avoid vagabond voltages!

Never use a power supply unit to power fieldbus nodes with PROFIsafe I/O
modules and fieldbus nodes with 230 V I/O modules.

6.2.2.1

230V AC I/O modules and PROFIsafe I/O modules are used together
in one fieldbus node

An isolation transformer (basic insulation) must be used to supply the voltage for
the 230 VAC I/O modules. Between adjoining 230 VAC and 24 VDC I/O
modules, you have to take into account the double basic insulation and if
necessary, use separation modules 750-616/030-000.

«
...
54
55
56
57
58
...
»

Содержание I/O-SYSTEM 750-666/000-003







































































































































































Отзывы:

Нет отзывов

Похожие инструкции для I/O-SYSTEM 750-666/000-003

PROFINET BNI PNT-508-055-P067

Бренд: Balluff Страницы: 84

Бренд: LAON TECHNOLOGY Страницы: 58

Бренд: Patton Страницы: 4

Бренд: Quantum Страницы: 97

Бренд: WAREMA Страницы: 4

Бренд: Zenitel Страницы: 11

Бренд: Zamel Страницы: 11

Бренд: V-Tec Страницы: 2

Бренд: KAPTARLIFT Страницы: 16

Бренд: Quickie Страницы: 108

NEOS DIGITAL KVD-2 S1 COAX

Бренд: Auta Страницы: 4

TRANSITIONS Angled Entry Mat

Бренд: EZ-ACCESS Страницы: 4

Бренд: RAM Страницы: 22

MoveAround MA50

Бренд: Safelift Страницы: 20

Бренд: Woodward Страницы: 84

Бренд: HIKVISION Страницы: 23

2CB5-S Replacement Cartridge EV9617-22

Бренд: Everpure Страницы: 2

Бренд: Bloomfield Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды