WAGO I/O-SYSTEM 750-666/000-003 Скачать руководство пользователя страница 91

Страница: 91 / 166

WAGO-I/O-SYSTEM 750

Commissioning

750-666/000-003 4FDI/2FDO 24V/10A PROFIsafe V2 iPar

Manual

Version 1.2.0, valid from HW/SW Version 01/01

Commissioning

7.1

Startup and Maintenance Instructions

Only qualified persons may perform the work!

Adding, exchanging and starting up PROFIsafe I/O modules may only be carried
out by personnel trained in safety-related procedures!

Check safety functions!

Before start up, all safety functions must be checked for their specified
effectiveness!

7.1.1

Proof Test

During the final inspection of the PROFIsafe I/O modules, the serial number with
the date of manufacture must be applied to the housing.

Serial number

- B000000

Calendar
week

Year Software

version

Hardware
version

Firmware
loader
version

Internal

number

Figure 45: Example of a serial number

The serial number consists of the week and year of manufacture, software version
(if available), hardware version, firmware loader version (if available) and other
internal information from WAGO Kontakttechnik GmbH & Co. KG.

Содержание I/O-SYSTEM 750-666/000-003







































































































































































Результаты поиска

Содержание I/O-SYSTEM 750-666/000-003

Отзывы:

Бренды по названию

Популярные бренды

WAGO I/O-SYSTEM 750-666/000-003, Руководство пользователя

Результаты поиска

Содержание I/O-SYSTEM 750-666/000-003

Отзывы:

Бренды по названию

Популярные бренды