WAGO I/O-SYSTEM 750-666/000-003 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 166

background image

WAGO-I/O-SYSTEM 750

Important Notes

13

750-666/000-003 4FDI/2FDO 24V/10A PROFIsafe V2 iPar

Manual

Version 1.2.0, valid from HW/SW Version 01/01

Operating 750 Series components in home applications without further measures
is only permitted if they meet the emission limits (emissions of interference)
according to EN 61000-6-3. You will find the relevant information in the section
on "WAGO-I/O-SYSTEM 750"



"System Description"



"Technical Data" in

the manual for the used fieldbus coupler/controller.

Appropriate housing (per 94/9/EG) is required when operating the WAGO-I/O-
SYSTEM 750 in hazardous environments. Please note that a prototype test
certificate must be obtained that confirms the correct installation of the system in
a housing or switch cabinet.

2.1.4

Technical Condition of Specified Devices

The components to be supplied Ex Works, are equipped with hardware and
software configurations, which meet the individual application requirements.
WAGO Kontakttechnik GmbH & Co. KG will be exempted from any liability in
case of changes in hardware or software as well as to non-compliant usage of
components.

Please send your request for modified and new hardware or software
configurations directly to WAGO Kontakttechnik GmbH & Co. KG.

«
...
11
12
13
14
15
...
»

Содержание I/O-SYSTEM 750-666/000-003







































































































































































Отзывы:

Нет отзывов

Похожие инструкции для I/O-SYSTEM 750-666/000-003

Бренд: Samsung Страницы: 60

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 24

Бренд: Samsung Страницы: 22

Бренд: Samsung Страницы: 23

Бренд: Underhill Страницы: 15

Бренд: bar Страницы: 2

Бренд: FAAC Страницы: 60

Бренд: FAAC Страницы: 68

Бренд: National Instruments Страницы: 15

Бренд: National Instruments Страницы: 20

Бренд: National Instruments Страницы: 22

NI PXI-665 Series

Бренд: National Instruments Страницы: 14

Бренд: National Instruments Страницы: 30

Бренд: National Instruments Страницы: 10

Бренд: National Instruments Страницы: 34

Бренд: M-system Страницы: 21

sundi FORTE GNT-223

Бренд: Zamel Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды