WAGO I/O-SYSTEM 750-666/000-003 Скачать руководство пользователя | Manualshive

Страница: 36 / 166

background image

36

Device Description

WAGO-I/O-SYSTEM 750

750-666/000-003 4FDI/2FDO 24V/10A PROFIsafe V2 iPar

Manual

Version 1.2.0, valid from HW/SW Version 01/01

4.6.7

Safety Parameters

4.6.8

Two-channel Safety Application, Proof Test-Interval 10
Years

Table 17: Safety parameters for two-channel safety application

Maximum Safety integrity Level
acc. EN 62061

SIL3

Maximum safety integrity level
acc. IEC 61508

SIL3

Maximum performance level
acc. EN ISO 13849-1

Cat. 4/PL e

Proof test interval

10 years

Probability of failure PFD,
Proof test interval 10 years,
(low demand mode) (IEC 61508)

for one two-channel output
  (fieldbus to output)

  for one input pair
  (input to fieldbus)

  for two input pairs and one
  two-channel output (intput to
  fieldbus and fieldbus to output)

8.46 * 10

-5

(8.5% of all

PFD from 10

-3

at SIL3)

5.71 * 10

-5

(5.71% of all

PFD from 10

-3

at SIL3)

8.50 * 10

-5

(8.5% of all

PFD from 10

-3

at SIL3)

Probability of failure PFH,
Proof test interval 10 years,
(low demand mode) (IEC 61508)

for one two-channel output
  (fieldbus to output)

  for one input pair
  (input to fieldbus)

  for two input pairs and one
  two-channel output (intput to
  fieldbus and fieldbus to output)

1.94 * 10

-9

(1.94% of all

PFH from 10

-7

at SIL3)

1.31 * 10-9 (1.31% of all
PFH from 10-7 at SIL3)

1.95 * 10-9 (1.95% of all
PFH from 10-7 at SIL3)

Hardware fault tolerance HFT with two-
channel application
(IEC 61508/EN ISO 13849-1)

1 (one error in the application does
not yet lead to a failure of the
safety equipment)

DC (diagnostic coverage level)

94%

MTTF

d

(Mean Time To Failure dangerous)

410 years

«
...
34
35
36
37
38
...
»

Содержание I/O-SYSTEM 750-666/000-003







































































































































































Отзывы:

Нет отзывов

Похожие инструкции для I/O-SYSTEM 750-666/000-003

Бренд: National Instruments Страницы: 8

Бренд: SAI Страницы: 16

Бренд: b-red Страницы: 7

Бренд: Laser Страницы: 2

FieldPoint FP-AI-100

Бренд: National Instruments Страницы: 17

Бренд: AmeriWater Страницы: 16

Бренд: ICP DAS USA Страницы: 2

Бренд: Commax Страницы: 8

Бренд: Sonos Страницы: 15

Бренд: Senju Sprinkler Страницы: 8

Universal XL HD Lifter

Бренд: Garage Smart Страницы: 21

Бренд: Sanela Страницы: 7

MR Confon Starter f MKII+

Бренд: Cambridge Research Systems Страницы: 34

Бренд: Crystal Страницы: 3

R7G4FML3-6-DA16

Бренд: M-system Страницы: 10

Бренд: M-system Страницы: 3

Бренд: ION Страницы: 16

Бренд: LEXMAN Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды