manualshive.com logo in svg

WAGO I/O-SYSTEM 750-666/000-003, Руководство пользователя

Поделиться
Скачать
WAGO I/O-SYSTEM 750-666/000-003 Скачать руководство пользователя страница 133

WAGO-I/O-SYSTEM 750 

Service  133 

750-666/000-003 4FDI/2FDO 24V/10A PROFIsafe V2 iPar 

 

 

Manual 

 

Version 1.2.0, valid from HW/SW Version 01/01 

 

10.1.2 

I/O Module with iPar Server Functionality 

10.1.2.1  PROFIsafe Address Set Using the Coding Switch 

If the PROFIsafe address of the I/O module to be replaced is set using the coding 
switch on the side, i.e., the switch setting does not equal 0, proceed with replacing 
the I/O module as follows: 

• 

Acknowledge the PROFIsafe communication error in the safe PLC. 

After acknowledging the error, the replacement I/O module automatically requests 
its individual parameters from the iPar server. The safety-related verification of 
these parameters occurs in the PROFIsafe I/O module. If the verification step is 
unsuccessful, the replacement I/O module sends a second request to the iPar 
server. If the process cannot be completed successfully, the replacement I/O 
module remains in its initial state and must be configured using the WAGO 
parameterization tool (see section "Parameterization of the PROFIsafe I/O 
Module with the WAGO Parameterization Tool"). 

10.1.2.2  PROFIsafe Address Set Using the Parameterization Tool 

If the setting of the coding switch of the I/O module to be replaced represents the 
value 0, the PROFIsafe address of the I/O module to be replaced must be set using 
the parameterization tool (see section "Parameterization of the PROFIsafe I/O 
Module with the WAGO Parameterization Tool"). After successfully setting the 
PROFIsafe address, proceed as follows: 

• 

Acknowledge the PROFIsafe communication error in the safe PLC. 

After acknowledging the error, the replacement I/O module automatically requests 
its individual parameters from the iPar server. The safety-related verification of 
these parameters occurs in the PROFIsafe I/O module. If the verification step is 
unsuccessful, the replacement I/O module sends a second request to the iPar 
server. If the process cannot be completed successfully, the replacement I/O 
module remains in its initial state and must be configured using the WAGO 
parameterization tool (see section "Parameterization of the PROFIsafe I/O 
Module with the WAGO Parameterization Tool"). 

10.1.3 

I/O Module without iPar Server Functionality 

10.1.3.1  PROFIsafe Address Set Using the Coding Switch 

If the PROFIsafe address of the I/O module to be replaced is set using the coding 
switch, i.e., the switch setting does not equal 0, use the WAGO parameterization 
tool to configure the replacement I/O module (see section "Parameterization of the 
PROFIsafe I/O Module with the WAGO Parameterization Tool"). 

10.1.3.2  PROFIsafe Address Set Using the Parameterization Tool 

If the setting of the coding switch of the I/O module to be replaced represents the 
value 0, the PROFIsafe address of the replacement I/O module must be set using 
the parameterization tool (see section "Parameterization of the PROFIsafe I/O 

Содержание I/O-SYSTEM 750-666/000-003







































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды