WAGO I/O-SYSTEM 750-666/000-003 Скачать руководство пользователя | Manualshive

Страница: 54 / 166

background image

54

Connect Devices

WAGO-I/O-SYSTEM 750

750-666/000-003 4FDI/2FDO 24V/10A PROFIsafe V2 iPar

Manual

Version 1.2.0, valid from HW/SW Version 01/01

Digital inputs O1 - O2 receive the 24 V field supply voltage through the CAGE
CLAMP

®

connections 24 V and 0 V on the right half of the enclosure.

Both supply points for the 24V field supply voltage are galvanically seperated
from each other and may by supplied by different PELV/SELV power supplies
from different phases.

Figure 19: Infeed for PROFIsafe I/O modules 75x-66x and 75x-666

If unregulated power supplies are used for the field supply voltage of the
WAGO-I/O-SYSTEM 750 are used or if voltage dips occur when switching
capacitive loads (e.g., interference-free modules with internal capacitors),
passivation of the PROFIsafe I/O modules can occur.

In such case, you must use a capacitor (200 µF per 1 A load current) to support
the field supply voltage for the digital inputs. You can use a back-up capacitor
module with a capacity of 10000 µF (Order No. 288-824). The back-up capacitor
module (Order No. 288 824) has a maximum current carrying capacity of 1 A and
may not be used to support the 24V field supply voltage for the digital power
outputs.

«
...
52
53
54
55
56
...
»

Содержание I/O-SYSTEM 750-666/000-003







































































































































































Отзывы:

Нет отзывов

Похожие инструкции для I/O-SYSTEM 750-666/000-003

Бренд: Cadman Страницы: 70

RDS17S-ELITE1-R1

Бренд: D&R ELECTRONICS Страницы: 12

Бренд: ORMA Страницы: 5

Бренд: Wesco Страницы: 20

Бренд: NaanDanJain Страницы: 12

BRAVO FT SB2 06

Бренд: Comelit Страницы: 16

Бренд: Valcom Страницы: 3

SupplyNet DS21-24

Бренд: Viking Страницы: 2

Cruisair SMX II

Бренд: Taylor Made Environmental Страницы: 36

Бренд: HADEF Страницы: 20

Бренд: UHPPOTE Страницы: 12

SL 400 Skylifter

Бренд: SmartLift Страницы: 23

Бренд: Relaxa Mobility Страницы: 8

Бренд: Vents Страницы: 20

Бренд: Midland Страницы: 92

Бренд: Commodore Страницы: 18

750-1417/040-000

Бренд: WAGO Страницы: 58

Бренд: Channel Vision Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды