manualshive.com logo in svg

WAGO I/O-SYSTEM 750-666/000-003, Руководство пользователя

Поделиться
Скачать
WAGO I/O-SYSTEM 750-666/000-003 Скачать руководство пользователя страница 93

WAGO-I/O-SYSTEM 750 

Commissioning 

93 

750-666/000-003 4FDI/2FDO 24V/10A PROFIsafe V2 iPar 

 

 

Manual 

 

Version 1.2.0, valid from HW/SW Version 01/01 

 

7.3 

Setting the PROFIsafe Address using the Coding 
Switch 

 

 

 

Disconnect the power from the node before making the settings! 

Switch off the fieldbus node before you pull the PROFIsafe I/O module out of the 
fieldbus node to change the settings! 

 

 

 

 

Use only appropriate tools to change the settings! 

To set the switching elements of the coding switch, use only suitable objects (e.g., 
test prod or watchmakers screwdriver). Never exert pressure on the switching 
elements. 

 

 

 

 

Coding switch is inaccessible when the I/O module is plugged in! 

To set the PROFIsafe address on the coding switch, the I/O module must be 
pulled out of the fieldbus node. 

Use the switching elements of the coding switch to set the PROFIsafe address to a 
value from 1 to 1023. 

7.3.1 

Setting the PROFIsafe Address using the WAGO 
Parameterization Tool 

 

 

 

Effectiveness using the WAGO Parameterization Tool 

The PROFIsafe address set using the WAGO parameterization tool only takes 
effect when the address set on the coding switch of the I/O module equals 0. 

To configure the PROFIsafe address through storage in the parameter data set of 
the I/O module, set the PROFIsafe address in the WAGO parameterization tool to 
the required value and save the current parameter data set to the I/O module. 

Configuring the PROFIsafe I/O module is described in the section 
"Parameterization with the WAGO Parameterization Tool". 

 

 

 

Содержание I/O-SYSTEM 750-666/000-003







































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды