WAGO I/O-SYSTEM 750-666/000-003 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 166

WAGO I/O-SYSTEM 750-666/000-003 Скачать руководство пользователя страница 7

WAGO-I/O-SYSTEM 750

Notes about this Documentation

7

750-666/000-003 4FDI/2FDO 24V/10A PROFIsafe V2 iPar

Manual

Version 1.2.0, valid from HW/SW Version 01/01

1

Notes about this Documentation

Keep this documentation!

The operating instructions are part of the product and shall be kept for the entire
lifetime of the device. They shall be transferred to each subsequent owner or user
of the device. Care must also be taken to ensure that any supplement to these
instructions are included, if applicable.

Technical Terms in this Documentation

The technical terms used in this documentation are available in the glossary at the
end of the manual.

1.1

Validity of this Documentation

This documentation is only applicable to the I/O module 750-666/000-003
(4FDI/2FDO 24V/10A PROFIsafe V2 iPar) of the WAGO-I/O-SYSTEM 750
series from HW/SW Version 01/01.

The I/O module 750-666/000-003 shall only be installed and operated according
to the instructions in this manual and in the manual for the used fieldbus
coupler/controller.

Consider power layout of the WAGO-I/O-SYSTEM 750!

In addition to these operating instructions, you will also need the manual for the
used fieldbus coupler/controller, which can be downloaded at

There, you can obtain important information including information on electrical
isolation, system power and supply specifications.

Observe the information on the power infeed concept!

Detailed information and examples for supplying PROFIsafe I/O modules is
available in the section "Power Infeed Concept".

1.2

Copyright

This Manual, including all figures and illustrations, is copyright-protected. Any
further use of this Manual by third parties that violate pertinent copyright
provisions is prohibited. Reproduction, translation, electronic and phototechnical
filing/archiving (e.g., photocopying) as well as any amendments require the
written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.
Non-observance will involve the right to assert damage claims.

«
...
5
6
7
8
9
...
»

Содержание I/O-SYSTEM 750-666/000-003







































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды