WAGO I/O-SYSTEM 750-666/000-003 Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 166

background image

WAGO-I/O-SYSTEM 750

Connect Devices

73

750-666/000-003 4FDI/2FDO 24V/10A PROFIsafe V2 iPar

Manual

Version 1.2.0, valid from HW/SW Version 01/01

Use the same value for the test pulse duration of output O1 and O2!

If the

Output Configuration

parameter is set to "H-Side/L-Side 1", the values of

the

Test pulse duration

for both outputs O1 and O2 must be set to the same

value. This is checked by the PROFIsafe I/O module during the parameterization
procedure and a suggested correction is indicated by the PROFIsafe I/O module in
the WAGO parameterization tool in case of deviation.

The value of the output tolerance time must not be less that the value of the
test pulse duration!

The value of the

Output tolerance time

parameter may not be less than the value

of the

Test pulse duration

parameter. This is checked by the PROFIsafe I/O

module during the parameterization procedure and a suggested correction is
indicated by the PROFIsafe I/O module in the WAGO parameterization tool in
case of deviation.

«
...
71
72
73
74
75
...
»

Содержание I/O-SYSTEM 750-666/000-003







































































































































































Отзывы:

Нет отзывов

Похожие инструкции для I/O-SYSTEM 750-666/000-003

Бренд: La Gard Страницы: 2

BIS U-830-4-011-H-1

Бренд: Balluff Страницы: 2

Бренд: Wenshing Страницы: 4

Бренд: Cobolt Страницы: 5

EVERPURE CONSERV LT-S

Бренд: Pentair Страницы: 20

Бренд: ADLINK Technology Страницы: 37

CompuScope 85GC

Бренд: Gage Страницы: 174

Бренд: Data Aire Страницы: 100

Бренд: Door Knox Страницы: 25

Бренд: Grundfos Страницы: 21

Бренд: Redback Страницы: 16

Бренд: PRASTEL Страницы: 20

Бренд: ICP DAS USA Страницы: 4

THOMSON DS120CD

Бренд: Bigben Страницы: 76

Бренд: Slinex Страницы: 27

Бренд: NuTone Страницы: 84

FlowXtreme NE4487

Бренд: Bluewave Страницы: 20

Бренд: Mohawk Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды