WAGO I/O-SYSTEM 750-666/000-003 Скачать руководство пользователя страница 126 | Manualshive

Страница: 126 / 166

background image

126 Diagnostics

WAGO-I/O-SYSTEM 750

750-666/000-003 4FDI/2FDO 24V/10A PROFIsafe V2 iPar

Manual

Version 1.2.0, valid from HW/SW Version 01/01

Table 41: Diagnostic messages

Alarm

Description

Differing
F_Dest_Add

Diagnostic
type

Module Diagnostics

Coding:

0x0040

LED
indication

Group error (E) red
PROFIsafe (G) red

Solution

The PROFIsafe address assigned as part of
the F parameterization differs from that set
on the F I/O module.. Check the DIP
switch setting or PROFIsafe address set
using the safety editor (SEDI).

Discrepancy time
exceeded

Diagnostic
type

Channel Diagnostics

Coding:

0x021E

LED
indication

Status In (A, B, C or D) red,
group error (E) red

Solution

For dual channel evaluation of the input
pair, the F I/O module has determined that
the discrepancy time set has been
exceeded. Check the connected contacts.
Adjust the discrepancy time setting if
necessary.

Incorrect
F_CRC_Length

Diagnostic
type

Module Diagnostics

Coding:

0x0045

LED
indication

Group error (E) red
PROFIsafe (G) red

Solution

The configured F_CRC length is not
possible in the current operating mode.
Observe the dependency between
F_Par_Version and F_CRC_Length and
select a valid combination.

Incorrect
F_Par_Version

Diagnostic
type

Module Diagnostics

Coding:

0x0046

LED
indication

Group error (E) red
PROFIsafe (G) red

Solution

The set version of the F parameter set is
incorrect. Observe the dependency
between F_Par_Version and
F_CRC_Length and select a valid
combination.

«
...
124
125
126
127
128
...
»

Содержание I/O-SYSTEM 750-666/000-003







































































































































































Отзывы:

Нет отзывов

Похожие инструкции для I/O-SYSTEM 750-666/000-003

Passport 500 Pro

Бренд: Fender Страницы: 4

MaestroKitchen 100

Бренд: Harman Kardon Страницы: 36

AZ8350 - Cd Radio Cass Recorder

Бренд: Magnavox Страницы: 18

Бренд: Reliance Foundry Страницы: 3

EtherCAT Compact67 Slim

Бренд: elco Страницы: 28

Бренд: Aiphone Страницы: 2

Бренд: AMX Страницы: 88

Бренд: Digital Acoustics Страницы: 14

Бренд: SCS Sentinel Страницы: 13

Бренд: WaterGroup Страницы: 24

Бренд: Magnavox Страницы: 25

Бренд: hager Страницы: 73

Бренд: Walkera Страницы: 22

Бренд: Blue Giant Страницы: 24

DE-3000+ Series

Бренд: Altronic Страницы: 77

Бренд: FARFISA INTERCOMS Страницы: 2

Бренд: PROLIFTS Страницы: 44

Бренд: FXConnectX Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды