WAGO I/O-SYSTEM 750-666/000-003 Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 166

background image

WAGO-I/O-SYSTEM 750

Connect Devices

67

750-666/000-003 4FDI/2FDO 24V/10A PROFIsafe V2 iPar

Manual

Version 1.2.0, valid from HW/SW Version 01/01

In this output configuration, the PROFIsafe I/O module switches both
semiconductor switches ON or OFF at the same time using the bit 0 of the output
process image.

If you want to disable line break detection for the load, set the

Line break

detection

parameter to "inactive". Otherwise, set the Line break detection

parameter to "active" so that the PROFIsafe I/O module performs the line break
detection task once per minute.
For more information about configuring the PROFIsafe I/O module, read section
"Parameterization of the PROFIsafe I/O Module with the WAGO
Parameterization Tool".

Please note that line break detection may not be part of the safety function under
any circumstances.

You can achieve a risk reduction of SIL3/Cat.4/PL e, for example, by reading
back the switching states of the power jumper contacts from positively driven
contacts of a relay.

Line break detection on the digital output

You must use the

Line break detection

parameter in the "H-Side/L-Side 1"

output configuration

to monitor line breaks between connections O1B or O2A to

the connected load.
Line break detection is not safety related and cannot be part of the safety function
under any circumstances.

Use the same value for the output tolerance time of output O1 and O2!

If the

Output Configuration

parameter is set to "H-Side/L-Side 1", the values of

the

Output tolerance time

for both outputs O1 and O2 must be set to the same

value. This is checked by the PROFIsafe I/O module during the parameterization
procedure and a suggested correction is indicated by the PROFIsafe I/O module in
the WAGO parameterization tool in case of deviation.

Use the same value for the test pulse duration of output O1 and O2!

If the

Output Configuration

parameter is set to "H-Side/L-Side 1", the values of

the

Test pulse duration

for both outputs O1 and O2 must be set to the same

value. This is checked by the PROFIsafe I/O module during the parameterization
procedure and a suggested correction is indicated by the PROFIsafe I/O module in
the WAGO parameterization tool in case of deviation.

«
...
65
66
67
68
69
...
»

Содержание I/O-SYSTEM 750-666/000-003







































































































































































Отзывы:

Нет отзывов

Похожие инструкции для I/O-SYSTEM 750-666/000-003

Бренд: Rain Bird Страницы: 9

Бренд: bar Страницы: 2

Бренд: JBL Страницы: 16

Authentics L 16

Бренд: JBL Страницы: 17

Бренд: Magnavox Страницы: 24

Бренд: Magnavox Страницы: 22

Бренд: Magnavox Страницы: 21

Magnavox FW 750C

Бренд: Magnavox Страницы: 28

Magnavox FW 2012

Бренд: Magnavox Страницы: 16

Бренд: Quantum Страницы: 97

Бренд: H3C Страницы: 8

Бренд: HAMPTON BAY Страницы: 16

Airedale Sentinel

Бренд: Modine Manufacturing Страницы: 2

BNI PNT-507-005-Z040

Бренд: Balluff Страницы: 2

Бренд: Ravaglioli Страницы: 72

Бренд: V-ZUG Страницы: 24

Бренд: WinSystems Страницы: 30

Бренд: Commax Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды