WAGO I/O-SYSTEM 750-666/000-003 Скачать руководство пользователя страница 5

Страница: 5 / 166

WAGO-I/O-SYSTEM 750

Table of Contents

750-666/000-003 4FDI/2FDO 24V/10A PROFIsafe V2 iPar

Manual

Version 1.2.0, valid from HW/SW Version 01/01

7.4.4

Indirect Start via WAGO-I/O-

CHECK

from the Operating System .. 98

7.4.4.1

Direct Start from the Operating System ........................................ 99

7.4.4.2

Indirect Start via WAGO-I/O-

CHECK

from the Configuration

Program (Device Level TCI Conformance Class 2) ...................... 99

7.4.4.3

Indirect Start via WAGO-I/O-

CHECK

from the Configuration

Program (Module Level TCI Conformance Class 2)..................... 99

7.4.4.4

Direct Start from the Configuration Program (Device Level TCI
Conformance Class 3) .................................................................... 99

7.4.4.5

Direct Start from the Configuration Program (Module Level TCI
Conformance Class 3) .................................................................. 100

7.4.4.6

Direct Start from the Configuration Program (Device Level TCI
Conformance Class 3 OFFLINE) ................................................ 100

7.4.4.7

Direct Start from the Configuration Program (Module Level TCI
Conformance Class 3 OFFLINE) ................................................ 100

7.4.5

Adjustable Parameters ...................................................................... 101

7.4.5.1

Input Filter Time Parameter ......................................................... 102

7.4.5.2

Short circuit Test Ix Parameter .................................................... 103

7.4.5.3

Parameter Dual Channel Evaluation Ix & Ix+1 ........................... 104

7.4.5.4

Parameter Discrepancy Time Ix & Ix+1 ...................................... 105

7.4.5.5

Parameter Valence Evaluation Ix & Ix+1 .................................... 107

7.4.5.6

Parameter Restart Inhibit Ix & Ix+1 ............................................ 108

7.4.5.7

Operating Mode Parameter .......................................................... 109

7.4.5.8

ParameterOutput Configuration Parameter ................................. 110

7.4.5.8.1

Output Configuration H-Side/L-Side 1 ................................... 110

7.4.5.8.2

Output Configuration H-Side/L-Side 2 ................................... 111

7.4.5.8.3

Output Configuration H-Side/H-Side 1 .................................. 112

7.4.5.8.4

Output Configuration H-Side/H-Side 2 .................................. 112

7.4.5.9

Output Tolerance Time Parameter ............................................... 113

7.4.5.10

Test Pulse Duration Parameter .................................................... 115

7.4.5.11

Line Break Detection Parameter .................................................. 116

7.5

Programming the Safe PLC .................................................................. 118

7.5.1

PROFIsafe I/O Module without iPar Functionality.......................... 118

7.5.2

PROFIsafe I/O Module with iPar Functionality and iPar Server ..... 119

7.5.3

PROFIsafe I/O Module with iPar Functionality without iPar Server120

Process Image ........................................................................................... 122

8.1

PROFIsafe V1 Mode ............................................................................. 122

8.2

PROFIsafe V2 Mode ............................................................................. 123

Diagnostics ................................................................................................ 124

9.1

Behavior in the Event of an Error ......................................................... 124

9.2

Diagnosis of Errors ............................................................................... 125

Service ....................................................................................................... 132

10.1

Replacing a PROFIsafe I/O Module ..................................................... 132

10.1.1

Procedure .......................................................................................... 132

10.1.2

I/O Module with iPar Server Functionality ...................................... 133

10.1.2.1

PROFIsafe Address Set Using the Coding Switch ...................... 133

10.1.2.2

PROFIsafe Address Set Using the Parameterization Tool .......... 133

10.1.3

I/O Module without iPar Server Functionality ................................. 133

10.1.3.1

PROFIsafe Address Set Using the Coding Switch ...................... 133

Содержание I/O-SYSTEM 750-666/000-003







































































































































































Результаты поиска

Содержание I/O-SYSTEM 750-666/000-003

Отзывы:

Похожие инструкции для I/O-SYSTEM 750-666/000-003

Бренды по названию

Популярные бренды

WAGO I/O-SYSTEM 750-666/000-003, Руководство пользователя

Результаты поиска

Содержание I/O-SYSTEM 750-666/000-003

Отзывы:

Похожие инструкции для I/O-SYSTEM 750-666/000-003

Бренды по названию

Популярные бренды