manualshive.com logo in svg

WAGO I/O-SYSTEM 750-666/000-003, Руководство пользователя

Поделиться
Скачать
WAGO I/O-SYSTEM 750-666/000-003 Скачать руководство пользователя страница 102

102  Commissioning 

WAGO-I/O-SYSTEM 750 

 

 

750-666/000-003 4FDI/2FDO 24V/10A PROFIsafe V2 iPar 

 

Manual 

 

Version 1.2.0, valid from HW/SW Version 01/01 

7.4.5.1 

Input Filter Time Parameter 

 

 

 

Configuring the input filter time changes the safe response time! 

If you change the Input Filter Time parameter, then the safe response time is also 
changed. See "Response Time" section. 

The 

Input Filter Time

 parameter is used to set the filter time for all digital inputs 

of the PROFIsafe I/O module. Setting the filter time to "0 ms" disables the input 
filter. 

Note that the minimum signal duration on a digital input depends on the filter time 
set.  
With the input filter, signal changes to a digital input are detected by the 
PROFIsafe I/O module delayed by the duration of the filter time. 

If the signal voltage on the digital input switches from "1" to "0" (signal change 
1-0) for a safety requirement (e.g., emergency off requirement), for example, 
signal voltage "0" must be present for this input pulse duration.  
If the signal voltage is present shorter than the input pulse duration on the digital 
input, the signal change is may not be detected by the PROFIsafe I/O module. The 
following table indicates input pulse durations depending on the input filter time 
set: 

Table 27: Input pulse durations depending on the input filter time 

Input filter time  
[ms] 

0 

0.5 

1 

2 

3 

5 

10 

20 

50  100  200 

Input pulse duration  
[ms] 

19 

20 

21 

24 

28 

36 

56 

96  216  418  816 

 

 

 

 

Use shielded cables for input filter times under 3 ms! 

If you have set input filter times under 3 ms, you have to use shielded cables if 
there is risk of interference (e.g., overvoltage) on the signal lines to prevent 
possible passivation of the PROFIsafe I/O module. 

 
 

 

Содержание I/O-SYSTEM 750-666/000-003







































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды