WAGO I/O-SYSTEM 750-666/000-003 Скачать руководство пользователя страница 109 | Manualshive

Страница: 109 / 166

background image

WAGO-I/O-SYSTEM 750

Commissioning 109

750-666/000-003 4FDI/2FDO 24V/10A PROFIsafe V2 iPar

Manual

Version 1.2.0, valid from HW/SW Version 01/01

The

Restart inhibit

parameter is used for the dual channel evaluation of two

digital inputs. The restart inhibit is then only used by the PROFIsafe I/O module if
you have set the value of the

Operating mode

parameter to "Standard" and the

value of the

Dual channel evaluation

parameter to "yes".

You can set the

Restart inhibit

parameter to "Yes" or "No".

If you have set the

Restart inhibit

parameter to "Yes", then the PROFIsafe I/O

module behaves as follows:

A fixed discrepancy error can only be acknowledged if the input signals have
taken the values listed in the following table.

Table 32: Necessary signal states for acknowledgement if the restart inhibit is set to "yes"

Input pair

Digital inputs:

Valence evaluation

I2

I1

I1 & I2

"1"

"0"

"Antivalent"

"0"

"0"

"Equivalent"

I4

I3

I3 & I4

"1"

"0"

"Antivalent"

"0"

"0"

"Equivalent"

If you have set the

Restart inhibit

parameter to "No", then acknowledgement of a

discrepancy error is successful once the deviation from the valence rule on the
digital inputs concerned not longer exists. You can set the value of the

Restart

inhibit

parameter for each input pair separately.

7.4.5.7

Operating Mode Parameter

Evaluation of the input signal state in the "Rotary table" operating mode!

If you have set the

Operating mode

to the "Rotary table" value, the temporal

logic evaluation of the signal state must be performed by a suitable function block
in the safe PLC. Under certain circumstances, you can use the process image of
the digital inputs without the suitable function blocks.

An overview for using PROFIsafe I/O modules in combination with a safe PLC is
summarized in an application note. This application note is available on the
Internet at

in the area "Service > Documentation > Application

Notes...".

You can use the

Operating mode

parameter to choose between safe standard

analysis of the digital inputs (single-channel, two-channel) and the specific
"Rotary table" operating mode.

If you want to use the digital inputs single-channel or two-channel, you must set
the

Operating mode

parameter to the "Standard" value.

«
...
107
108
109
110
111
...
»

Содержание I/O-SYSTEM 750-666/000-003







































































































































































Отзывы:

Нет отзывов

Похожие инструкции для I/O-SYSTEM 750-666/000-003

Бренд: K-array Страницы: 20

Бренд: Waterway Страницы: 8

Бренд: CAME BPT Страницы: 16

Бренд: GSK Страницы: 32

Бренд: Locinox Страницы: 63

Бренд: FARFISA INTERCOMS Страницы: 2

Бренд: POBEL Страницы: 9

Nitrogen Pac SC-W

Бренд: UNITED Страницы: 112

Бренд: ESP Страницы: 24

Бренд: Kogan Страницы: 12

Бренд: Hama Страницы: 53

Бренд: Dahua Technology Страницы: 10

Бренд: M-system Страницы: 10

Бренд: iSMA Страницы: 73

Бренд: Samsung Страницы: 12

Бренд: Samsung Страницы: 14

Бренд: Samsung Страницы: 20

Бренд: Samsung Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды