SMC Corporation LECSA series Скачать руководство пользователя

Страница: 84 / 419

3 - 30

3. SIGNALS AND WIRING

3.6.3 Internal torque control mode
(1) Internal torque command settings

Torque is controlled by the internal torque command set in parameter No. PC12.

If the internal torque command is small, the torque may vary when the actual speed reaches the speed limit

value. In such case, increase the speed limit value.

The following table indicates the torque generation directions determined by the forward rotation selection

(RS1) and the reverse rotation selection (RS2) when the internal torque command (parameter No. PC12) is

used.

(Note) Input device

Rotation direction

Forward rotation (CCW)

Reverse rotation (CW)

RS2

RS1

Internal torque command (parameter No. PC12)

0.1 to 100.0%

0.0%

Torque is not generated.

Torque is not

generated.

CCW (reverse rotation in driving

mode/forward rotation in

regenerative mode)

CW (forward rotation in driving

mode/reverse rotation in

regenerative mode)

Torque is not generated.

Note. 0: off

1: on

Generally, make connection as shown below.

RS2

DOCOM

DICOM

Servo amplifier

RS1

24VDC

(Note)

Note. For the sink I/O interface. For the source I/O interface, refer to section 3.8.3.

The following shows the effect of the low-pass filter on the internal torque command.

Torque

Forward rotation/reverse
rotation selection

Internal torque command after filtered

Internal torque command (parameter No. PC12)

ON
OFF

Torque command time constant (parameter No. PC04)

(RS1/RS2)

(2) Torque limit

By setting parameter No. PA11 (forward torque limit) or parameter No. PA12 (reverse torque limit), torque

is always limited to the maximum value during operation. A relationship between limit value and servo

motor torque is as in section 3.6.1 (4).

Driver

Содержание LECSA series




































































































































































































































































































































































































































Результаты поиска

Содержание LECSA series

Отзывы:

Похожие инструкции для LECSA series

Бренды по названию

Популярные бренды

SMC Corporation LECSA series, Руководство по эксплуатации

Результаты поиска

Содержание LECSA series

Отзывы:

Похожие инструкции для LECSA series

Бренды по названию

Популярные бренды