Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 286

Страница: 286 / 346

Service and maintenance

8.3 Replacing the Power Module

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN

284

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

8.3

Replacing the Power Module

Procedure for replacing a Power Module

●

Disconnect the Power Module from the line supply.

●

If being used, switch off the 24 V supply of the Control Unit.

DANGER

Risk of electrical shock!
Hazardous voltage is still present for up to 5 minutes after the power supply has been

switched off.
It is not permissible to carry out any installation work before this time has expired!

●

Remove the connecting cables of the Power Module.

●

Remove the Control Unit from the Power Module.

●

Replace the old Power Module with the new Power Module.

●

Snap the Control Unit onto the new Power Module.

●

Connect up the new Power Module using the connecting cables.

●

Switch on the line supply and, if being used, the 24 V supply for the Control Unit.

●

If necessary, recommission the drive (also see Overview of replacing converter

components (Page 281)).

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы:

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 286 / 346

Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы: