manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 105 / 346

Поделиться
Скачать
Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 105

 

Configuring the fieldbus 

 

6.1 Communication via PROFIBUS 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

103

 

Control word 1 (STW1)  

Control word 1 (bits 0 … 10 in accordance with PROFIdrive profile and VIK/NAMUR, bits 11 

… 15 specific to inverter). 

Table 6- 6 

Control word 1 and interconnection with parameters in the inverter  

Significance 

Bit  Value 

Telegram 20  All other telegrams

Comments 

P No. 

0 

OFF1 

Motor brakes with the ramp-down time p1121 at 

standstill (f < f

min

) the motor is switched off. 

0 

1 

ON 

With a positive edge, the inverter goes into the "ready" 

state, with additionally bit 3 = 1, the inverter switches on 

the motor. 

p0840[0] = 

r2090.0 

0 

OFF2 

Switch off motor immediately, motor coasts to a 

standstill. 

1 

1 

No OFF2 

--- 

p0844[0] = 

r2090.1 

0 

Quick stop (OFF3) 

Quick stop: Motor brakes with the OFF3 ramp-down 

time p1135 down to standstill. 

2 

1 

No quick stop (OFF3) 

--- 

p0848[0] = 

r2090.2 

0 

Disable operation 

Immediately switch-off motor (cancel pulses). 

3 

1 

Enable operation 

Switch-on motor (pulses can be enabled). 

p0852[0] = 

r2090.3 

0 

Lock ramp-function generator 

The ramp-function generator output is set to 0 (quickest 

possible deceleration). 

4 

1 

Operating condition 

Ramp-function generator can be enabled 

p1140[0] = 

r2090.4 

0 

Stop ramp-function generator 

The output of the ramp-function generator is "frozen". 

5 

1 

Ramp-function generator enable 

 

p1141[0] = 

r2090.5 

0 

Inhibit setpoint 

Motor brakes with the ramp-down time p1121. 

6 

1 

Enable setpoint 

Motor accelerates with the ramp-up time p1120 to the 

setpoint. 

p1142[0] = 

r2090.6 

7  1 

Acknowledging faults 

Fault is acknowledged with a positive edge. If the ON 

command is still active, the inverter switches to"closing 

lockout" state. 

p2103[0] = 

r2090.7 

8   

Not used 

9   

Not used 

0 

PLC has no master control 

Process data invalid, "sign of life" expected. 

10 

1 

Master control by PLC 

Control via fieldbus, process data valid. 

p0854[0] = 

r2090.10 

11  1 

---

1)

 

Direction reversal  Setpoint is inverted in the inverter. 

p1113[0] = 

r2090.11 

12   

Not used 

13  1 

---

1)

 

MOP up 

The setpoint stored in the motorized potentiometer is 

increased. 

p1035[0] = 

r2090.13 

14  1 

---

1)

 

MOP down 

The setpoint stored in the motorized potentiometer is 

decreased. 

p1036[0] = 

r2090.14 

15  1 

CDS bit 0 

Not used 

Changes over between settings for different operation 

interfaces (command data sets). 

p0810 = 

r2090.15 

1)

  If you change over from another telegram to telegram 20, then the assignment of the previous telegram is kept. 

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Отзывы:

Нет отзывов