manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 284 / 346

Поделиться
Скачать
Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 284

Service and maintenance 

 

8.2 Replacing the Control Unit 

 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 

282

 

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

8.2

 

Replacing the Control Unit  

 

WARNING 

 

230 V AC can be connected via the relay outputs DO 0 and DO 2 of the Control Unit. These 

terminals can carry 230 V AC independent of the voltage condition of the Power Module. 

Therefore please observe appropriate safety measures when working on the inverter. 

 

After commissioning has been completed, we recommend that you back up your settings on 

an external storage medium, e.g.: on a memory card or the operator panel.  
If you do not back up your data, you have to recommission the drive when you replace the 

Control Unit. 

Procedure for replacing a Control Unit with a memory card 

●

 

Disconnect the line voltage of the Power Module and (if installed) the external 24 V 

supply or the voltage for the relay outputs DO 0 and DO 2 of the Control Unit. 

●

 

Remove the signal cables of the Control Unit. 

●

 

Remove the defective CU from the Power Module. 

●

 

Plug the new CU on to the Power Module. The new CU must have the same order 

number and the same or a higher firmware version as the CU that was replaced. 

●

 

Remove the memory card from the old Control Unit and insert it in the new Control Unit. 

●

 

Reconnect the signal cables of the Control Unit. 

●

 

Connect up the line voltage again. 

●

 

The converter adopts the settings from the memory card, saves them (protected against 

power failure) in its internal parameter memory, and switches to "ready to start" state. 

●

 

Switch on the motor and check the function of the drive. 

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Отзывы:

Нет отзывов