manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 220 / 346

Поделиться
Скачать
Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 220

Functions 

 

7.8 Status messages 

 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 

218

 

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

7.8

 

Status messages 

Information about the inverter state (alarms, faults, actual values) can be output via inputs 

and outputs and also via the communication interface. 
Details on evaluating the inverter state via inputs and outputs are provided in Section 

Adapting the terminal strip (Page 85). 
The evaluation of the inverter state via the communication interface is realized using the 

inverter status word. Details on this are provided in the individual sections of Chapter 

Configuring the fieldbus (Page 97). 

7.8.1

 

System runtime 

By evaluating the system runtime of the inverter, you can decide when you should replace 

components subject to wear in time before they fail - such as fans, motors and gear units. 

Principle of operation 

The system runtime is started as soon as the Control Unit power supply is switched-on. The 

system runtime stops when the Control Unit is switched off. 
The system runtime comprises r2114[0] (milliseconds) and r2114[1] (days): 
System runtime = r2114[1] × days + r2114[0] × milliseconds  
If r2114[0] has reached a value of 86,400,000 ms (24 hours), r2114[0] is set to the value 0 

and the value of r2114[1] is increased by 1. 

 

Parameter 

Description 

r2114[0] 

System runtime (ms) 

r2114[1] 

System runtime (days) 

You cannot reset the system runtime. 

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Отзывы:

Нет отзывов