Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 233

Страница: 233 / 346

Functions

7.9 Application-specific functions

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

231

DC braking parameters

Table 7- 34 Parameters for configuring DC braking

Parameter Description
p1230

Activate DC braking (BICO parameter)
The value for this parameter (0 or 1) can be either entered directly or specified by

means of an interconnection with a control command.

p1231

Configure DC braking

•

p1231 = 0, no DC braking

•

p1231 = 4, general enabling of DC braking

•

p1231 = 5, DC braking for OFF1/3, independent of p1230

•

P1231 = 14, enables DC braking for the case that the motor speed falls below the
start speed for DC braking.

Table 7- 35 Parameters for configuring DC braking in the event of faults

Parameter Description
p2100

Set fault number for fault reaction (factory setting: 0)
Enter the fault number for which DC braking should be activated, e.g.: p2100[3] = 7860

(external fault 1).

p2101 = 6 Fault reaction setting (factory setting: 0)

Assigning the fault response: p2101[3] = 6.

The fault is assigned an index of p2100. The associated fault response must be assigned the same

index in p2101.
In the List Manual of the inverter - in the "Faults and alarms" list - possible fault responses are listed

for every fault. The entry "DCBRAKE" means that for this particular fault, DC braking can be set as

fault response.

Table 7- 36 Additional parameters for setting DC braking

Parameter Description
p1232

DC braking braking current (factory setting: 0 A)

Setting the braking current for the DC braking.

p1233

DC braking duration (factory setting: 1 s)

p1234

DC braking start speed (factory setting: 210000 rpm)

DC braking starts – assuming that it has been correspondingly parameterized

(p1230/p1231) – as soon as the actual speed falls below this threshold.

p0347

Motor de-excitation

The parameter is calculated via p0340 = 1, 3.
The inverter can trip due to an overcurrent during DC braking if the de-excitation time is

too short.

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы:

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 233 / 346

Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы: