Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 337

Страница: 337 / 346

Appendix

A.1 Application examples

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

335

①

Activate the tab "Address

configuration".

②

Select line 1.

③

Open the dialog box in which you

define the Publisher and the address

area to be transferred.

①

Select DX for direct data exchange

②

Select the PROFIBUS address of

drive 1 (publisher).

③

In the address field, select the start

address specifying the data area to be

received from drive 1. In the example,

these are the status word 1 (PZD1)

and the speed actual value with the

start address 256.

Close both screen forms with OK. You have now defined the value range for slave-to-slave

communication.
In the slave-to-slave communication, drive 2 receives the sent data and writes this into the

next available words, in this case, PZD3 and PZD4.

Settings in drive 2 (subscriber)

Drive 2 is preset in such a way that it receives its setpoint from the higher-level control. In

order that drive 2 accepts the actual value sent from drive 1 as setpoint, you must set the

following:
●

In drive 2 ,set the PROFIdrive telegram selection to "Free telegram configuration with

BICO" (p0922 = 999).

●

In drive 2, set the source of the main setpoint to p1070 = 2050.3.

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы:

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 337 / 346

Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы: