Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 127

Страница: 127 / 346

Configuring the fieldbus

6.2 Communication via RS485

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

125

If the response ID = 7, then the inverter sends one of the error numbers listed in the

following table in parameter value 2 (PWE2).

Table 6- 23 Error numbers for the response "Request cannot be processed"

No.

Description

Comments

Impermissible parameter number (PNU)

Parameter does not exist

Parameter value cannot be changed

The parameter can only be read

Minimum/maximum not achieved or

exceeded

–

Wrong subindex

–

No field

An individual parameter was addressed with

a field request and subindex > 0

Wrong parameter type / wrong data type Confusion of word and double word

Setting is not permitted (only resetting)

Index is outside the parameter field[]

The descriptive element cannot be

changed

Description cannot be changed

Not in the "master control" mode

Change request without "master control" state

Keyword missing

–

Request cannot be processed on account

of the operating state

The actual inverter operating state is not

compatible with the received request

Illegal value

Modification access with a value which is

within the value limits but which is illegal for

other permanent reasons (parameter with

defined individual values)

101

Parameter number is currently

deactivated

Dependent on the operating state of the

inverter

102

Channel width is insufficient

Communication channel is too small for

response

104

Illegal parameter value

The parameter can only assume certain

values.

106

Request not included / task is not

supported

After request identifier 5,11,12,13,14,15

107

No write access with enabled controller

The operating state of the inverter prevents a

parameter change

200/201 Changed minimum/maximum not

achieved or exceeded

The maximum or minimum can be limited

further during operation.

204

The available access authorization does

not cover parameter changes.

–

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы:

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 127 / 346

Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы: