manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 161 / 346

Поделиться
Скачать
Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 161

 

Configuring the fieldbus 

 

6.3 Communication over CANopen 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

159

 

0607 0012h 

Data type does not match, length of service parameter too high. 
Data type is not correct, service parameter is too long 

0607 0013h   Data type does not match, length of service parameter too low. 

Data type is not correct, service parameter is too short 

0609 0011h 

Subindex does not exist 
Subindex does not exist 

0609 0030h 

Value range of parameter exceeded (only for write access). 
Value range of the parameter exceeded (only for write access) 

0609 0031h 

Value of parameter written too high. 
Subindex does not exist 

0609 0032h 

Value of parameter written too low. 
Value of written parameter too low 

0609 0036h 

Maximum value is less than minimum value. 
Maximum value is less than the minimum value 

0800 0000h 

General error. 
General error 

0800 0020h 

Data cannot be transferred or stored to the application. 
Data cannot be transferred or saved in the application 

0800 0021h 

Data cannot be transferred or stored to the application because of local control. 
Data cannot be transferred or saved due to the local control 

0800 0022h 

Data cannot be transferred or stored to the application because of the current device 

state. 
Data cannot be transferred or saved due to the device condition 

0800 0023h 

Object dictionary dynamic generation failed or no object dictionary is present (e.g. 

object dictionary is generated from file and generation fails because of a file error). 
Dynamic creation of the object dictionary failed - or an object dictionary does not exist 

(e.g. object directory was generated from a defective file)  

6.3.2.4

 

Access to SINAMICS parameters via SDO 

If you wish to change inverter parameters in CANopen using the control, then use the 

service data objects (SDO). SDO are transferred in the operational as well as in the pre-

operational states.  
You can also configure RPDO and TPDO telegrams via SDO. You can find the objects that 

are available to do this in Section Object directories (Page 170).  

Adapting the parameter numbers  

The inverter parameters can be addressed via the SDO parameter channel in the range from 

2000 hex ... 470F hex of the CANopen object directory. 

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Отзывы:

Нет отзывов