manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 295 / 346

Поделиться
Скачать
Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 295

 

Alarms, faults and system messages 

 

9.3 Faults 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

293

 

)DXOWEXIIHU

6KLIWRUFRS\
IDXOWVLQWRWKH
IDXOWKLVWRU\

'HOHWH
ROGHVWIDXOWV

)DXOWKLVWRU\

1HZHVWIDXOWV

2OGHVWIDXOWV

$FNQRZOHGJH

IDXOW

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

 

Figure 9-8 

Fault history after acknowledging the faults 

After acknowledgement, the faults that have not been removed are located in the fault buffer 

as well as in the fault history. For these faults, the "fault time coming" remains unchanged 

and the "fault time removed" remains empty. 
If less than eight faults were shifted or copied into the fault history, the memory locations with 

the higher indices remain empty. 
The inverters shifts the values previously saved in the fault history each by eight indices. 

Faults, which were saved in indices 56 … 63 before the acknowledgement, are deleted. 

Deleting the fault history 
If you wish to delete all faults from the fault history, set parameter p0952 to zero. 

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Отзывы:

Нет отзывов