manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 300 / 346

Поделиться
Скачать
Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 300

Alarms, faults and system messages 

 

9.4 List of alarms and faults 

 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 

298

 

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

Number  Cause 

Remedy 

F07011 

Motor overtemperature 

Reduce the motor load. 
Check ambient temperature. 
Check the wiring and connection of the sensor. 

A07012 

I2t Motor Module overtemperature  Check and if necessary reduce the motor load.  

Check the motor's ambient temperature. 
Check thermal time constant p0611. 
Check overtemperature fault threshold p0605. 

A07015 

Motor temperature sensor alarm 

Check that the sensor is connected correctly. 
Check the parameter assignment (p0601). 

F07016 

Motor temperature sensor fault 

Make sure that the sensor is connected correctly. 
Check the parameterization (p0601). 
Deactivate the temperature sensor fault (p0607 = 0). 

F07086 

F07088 

Unit switchover: Parameter limit 

violation 

Check the adapted parameter values and if required correct. 

F07320 

Automatic restart aborted 

Increase the number of restart attempts (p1211). The actual number of 

start attempts is shown in r1214. 
Increase the wait time in p1212 and/or monitoring time in p1213. 
Connect an ON command (p0840). 
Increase the monitoring time of the power unit or switch off (p0857). 
Reduce the wait time for resetting the fault counter p1213[1] so that fewer 

faults are registered in the time interval. 

A07321 

Automatic restart active 

Explanation: The automatic restart (AR) is active. During voltage recovery 

and/or when remedying the causes of pending faults, the drive is 

automatically switched back on. 

F07330 

Search current measured too low 

Increase search current (p1202), check motor connection. 

A07400 

V

DC_max

 controller active 

If it is not desirable that the controller intervenes: 

•

 

Increase the ramp-down times. 

•

 

Deactivate the V

DC_max

 controller (p1240 = 0 for vector control, p1280 

= 0 for U/f control). 

A07409 

U/f control, current limiting 

controller active 

The alarm automatically disappears after one of the following measures: 

•

 

Increase the current limit (p0640). 

•

 

Reduce the load. 

•

 

Slow down the up ramp for the setpoint speed. 

F07426 

Technology controller actual value 

limited 

•

 

Adapt the limits to the signal level (p2267, p2268). 

•

 

Check the actual value scaling (p2264). 

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Отзывы:

Нет отзывов