Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 187

Страница: 187 / 346

Functions

7.2 Inverter control

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

185

7.2

Inverter control

If you are controlling the inverter using digital inputs, you use parameter p0015 during basic

commissioning to define how the motor is switched on and off and how it is changed over

from clockwise to counter-clockwise rotation.
Five different methods are available for controlling the motor. Three of the five methods just

require two control commands (two-wire control). The other two methods require three

control commands (three-wire control).

Table 7- 1

Two-wire control and three-wire control

Behavior of the motor

&ORFNZLVH

URWDWLRQ

&RXQWHU

FORFNZLVH

URWDWLRQ

6WRS

Control commands

Typical

application

0RWRURQRII

5HYHUVLQJ

Two-wire control, method 1
1.

Switch the motor on and off

(ON/OFF1).

Reverse the motor direction of

rotation.

Local control in

conveyor

systems.

0RWRURQRII

FORFNZLVH

URWDWLRQ

0RWRURQRII

FRXQWHU

FORFNZLVH

URWDWLRQ

Two-wire control, method 2 and

two-wire control, method 3
1.

Switch the motor on and off

(ON/OFF1), clockwise rotation.

Switch the motor on and off

(ON/OFF1), counter-clockwise

rotation.

Traction drives

with control via

joystick

0RWRURQ

FORFNZLVH

URWDWLRQ

(QDEOH

PRWRURII

0RWRURQ

FRXQWHU

FORFNZLVH

URWDWLRQ

Three-wire control, method 1
1.

Issue enable for switching on motor

and switch off motor (OFF1).

Switch on motor (ON), clockwise

rotation.

Switch on motor (ON), counter-

clockwise rotation.

Traction drives

with control via

joystick

0RWRURQ

(QDEOH

PRWRURII

5HYHUVLQJ

Three-wire control, method 2
1.

Issue enable for switching on motor

and switch off motor (OFF1).

Switch on motor (ON).

Reverse the motor direction of

rotation.

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы:

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 187 / 346

Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы: