Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 60

Страница: 60 / 346

Commissioning

4.2 Preparing for commissioning

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

4.2.1

Inverter factory setting

Factory settings of additional important parameters

Parameter Factory setting Meaning of the factory

setting

Name of the parameter and comments

p0010

Ready to be entered

Drive, commissioning parameter filter

p0100

Europe [50 Hz]

IEC/NEMA motor standard

•

IEC, Europe

•

NEMA, North America

Note: This parameter cannot cannot be changed in FW4.3.

p0300

Induction motor

Motor type selection (induction motors / synchronous motor)

p0304

400

[V]

Rated motor voltage (in accordance with the rating plate in V)

p0305

depends on the

Power Module

[A]

Rated motor current (in accordance with the rating plate in A)

p0307

depends on the

Power Module

[kW/hp]

Rated motor power (in accordance with the rating plate in

kW/hp)

p0308

[cos phi]

Rated motor power factor (in accordance with the rating plate in

cos 'phi'). If p0100 = 1, 2, then p0308 has no significance.

p0310

[Hz]

Rated motor frequency (in accordance with the rating plate in

Hz)

p0311

1395

[rpm]

Rated motor speed (in accordance with the rating plate in rpm)

p0335

Non-ventilated: Shaft-

mounted fan in the motor

Motor cooling type (specify the motor cooling system)

p0625

[°C]

Motor ambient temperature

p0640

200

[A]

Current limit (of the motor)

p0970

Locked

Reset drive parameters (restore to the factory settings)

P1080

[rpm]

Minimum speed

P1082

1500

[rpm]

Maximum speed

P1120

[s]

Ramp-function generator, ramp-up time

P1121

[s]

Ramp-function generator, ramp-down time

P1300

V/f control with linear

characteristic

Open-loop/closed-loop control operating mode

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы:

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 60 / 346

Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы: