Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 299

Страница: 299 / 346

Alarms, faults and system messages

9.4 List of alarms and faults

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

297

Table 9- 10 The most important alarms and faults

Number Cause

Remedy

F01018

Power-up aborted more than once 1.

Switch the module off and on again.

After this fault has been output, the module is booted with the factory

settings.

Recommission the converter.

A01028

Configuration error

Explanation: Parameterization on the memory card has been created with

a different type of module (order number, MLFB)
Check the module parameters and recommission if necessary.

F01033

Unit switchover: Reference

parameter value invalid

Set the value of the reference parameter not equal to 0.0 (p0304, p0305,

p0310, p0596, p2000, p2001, p2002, p2003, r2004).

F01034

Unit switchover: Calculation of the

parameter values after reference

value change unsuccessful

Select the value of the reference parameter so that the parameters

involved can be calculated in the per unit notation (p0304, p0305, p0310,

p0596, p2000, p2001, p2002, p2003, r2004).

F01122

Frequency at the probe input too

high

Reduce the frequency of the pulses at the probe input.

A01590

Motor maintenance interval lapsed Carry out maintenance and reset the maintenance interval (p0651).

A01900

PROFIBUS: Configuration

telegram faulty

Explanation: A PROFIBUS master is attempting to establish a connection

with a faulty configuration telegram.
Check the bus configuration on the master and slave side.

A01910

F01910

Setpoint timeout

The alarm is generated when p2040 ≠ 0 ms and one of the following

causes is present:

•

The bus connection is interrupted

•

The MODBUS master is switched off

•

Communications error (CRC, parity bit, logical error)

•

An excessively low value for the fieldbus monitoring time (p2040)

A01920

PROFIBUS: Cyclic connection

interrupt

Explanation: The cyclic connection to PROFIBUS master is interrupted.
Establish the PROFIBUS connection and activate the PROFIBUS master

with cyclic operation.

F03505

Analog input, wire break

Check the connection to the signal source for interrupts.

Check the level of the signal supplied.

The input current measured by the analog input can be read out in r0752.

A03520

Temperature sensor fault

Check that the sensor is connected correctly.

A05000

A05001

A05002

A05004

A05006

Power Module overtemperature

Check the following:

- Is the ambient temperature within the defined limit values?

- Are the load conditions and duty cycle configured accordingly?

- Has the cooling failed?

F06310

Supply voltage (p0210) incorrectly

parameterized

Check the parameterized supply voltage and if required change (p0210).
Check the line voltage.

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы:

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 299 / 346

Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы: