manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 157 / 346

Поделиться
Скачать
Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 157

 

Configuring the fieldbus 

 

6.3 Communication over CANopen 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

155

 

6.3.2.2

 

Monitoring the communication and response of the inverter 

The communication monitoring can be used via both node guarding and heartbeat protocol 

(heartbeat producer). 

Node guarding 
The master sends monitoring queries to the slaves via the node guarding protocol.  
If the converter does not receive a Node Guarding protocol within the Life Time, then it 

outputs fault (F08700). 
Life Time = Guard time (p8601.0) * Life Time Factor (p8604.1) 

Heartbeat 
The slave periodically sends heartbeat messages. Other slaves and the master can monitor 

this message. If a heartbeat goes missing, then appropriate responses can be set in the 

master. 
The settings for the heartbeat protocol are made in parameter p8606. 
Note 

 

 

Note 
Node guarding and heartbeat are mutually interlocked. This means that if the parameter for 

one of these functions is not equal to 0, then the other cannot be used. 
Both functions are deactivated in the factory setting. 

 

Converter response to a bus fault - CAN controller state "Bus off"  
(converter fault F8700, fault value 1) 

If you acknowledge the bus fault using OFF/ON, the bus OFF state is also canceled and 

communication is restarted. 
If you acknowledge the bus fault via DI 2 or directly via p3981, then the converter remains in 

the bus OFF state. To restart communication, in this case, you must set p8608 to 1. 

 

WARNING 

 

If you acknowledge the bus fault via DI 2 or directly via p3981 - and p8641 is set to 0 (for a 

bus fault, the converter does not go into a fault condition), then you must restart 

communication via p8608 = 1 before you can stop the motor via the control.  

 

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Отзывы:

Нет отзывов