manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 238 / 346

Поделиться
Скачать
Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 238

Functions 

 

7.9 Application-specific functions 

 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 

236

 

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

7.9.2.5

 

Braking with regenerative feedback to the line 

Regenerative braking is typically used in applications where braking energy is generated 

either frequently or for longer periods of time, e.g.: 
●

 

Centrifuges 

●

 

Unwinders  

●

 

Cranes and hoisting gear  

Pre-requisite for regenerative braking is the Power Module PM250 or PM260.  
The inverter can feed back up to 100% of its power into the line supply (referred to "High 

Overload" base load, see Section Technical data, Power Modules (Page 305)). 

Parameterization of braking with regenerative feedback to the line 

Table 7- 38  Settings for braking with regenerative feedback to the line 

Parameter  Description 
Limiting the regenerative feedback for V/f control (P1300 < 20) 
p0640 

Motor overload factor 
Limiting the regenerative power is not directly possible with V/f control, but can be 

achieved indirectly by limiting the motor current. 
If the current exceeds this value for longer than 10 s, the inverter shuts down the motor 

with fault message F07806. 

Limiting feedback with vector control (P1300 ≥ 20) 
P1531 

Regenerative power limit 
The maximum regenerative load is entered as negative value via p1531. 

(-0.01 … -100000.00 kW). 
Values higher than the rated value of the power unit (r0206) are not possible. 

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Отзывы:

Нет отзывов