manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 207 / 346

Поделиться
Скачать
Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 207

 

Functions 

 

7.6 Motor control 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

205

 

It is not permissible to use vector control in the following cases: 

●

 

If the motor is too small in comparison to the inverter (the rated motor power may not be 

less than one quarter of the rated inverter power) 

●

 

If several motors are connected to one inverter 

●

 

If a power contactor is used between the inverter and motor and is opened while the 

motor is powered up 

●

 

If the maximum motor speed exceeds the following values: 

 

Inverter pulse frequency 

2 kHz 

4 kHz and higher 

Pole number of the motor 

2-pole 

4-pole 

6-pole 

2-pole 

4-pole 

6-pole 

Maximum motor speed [rpm] 

9960 

4980 

3320 

14400 

7200 

4800 

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Отзывы:

Нет отзывов