Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 298

Страница: 298 / 346

Alarms, faults and system messages

9.4 List of alarms and faults

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN

296

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

9.4

List of alarms and faults

Axxxxx Alarm
Fyyyyy: Fault

Table 9- 9

Faults, which can only be acknowledged by switching the inverter off and on again (power on reset)

Number Cause

Remedy

F01000

Software fault in CU

Replace CU.

F01001

Floating Point Exception

Switch CU off and on again.

F01015

Software fault in CU

Upgrade firmware or contact technical support.

F01018

Power-up aborted more than once After this fault has been output, the module is booted with the factory

settings.
Remedy: Back up factory setting with p0971=1. Switch CU off and on

again. Recommission the inverter.

F01040

Parameters must be saved

Save parameters (p0971).

Switch CU off and on again.

F01044

Loading of memory data card

defective

Replace memory card or CU.

F01105

CU: Insufficient memory

Reduce number of data records.

F01205

CU: Time slice overflow

Contact technical support.

F01250

CU hardware fault

Replace CU.

F01512

An attempt has been made to

establish an conversion factor for

scaling which is not present

Create scaling or check transfer value.

F01662

CU hardware fault

Switch CU off and on again, upgrade firmware, or contact technical

support.

F30022

Power Module: Monitoring U

Check or replace the Power Module.

F30052

Incorrect Power Module data

Replace Power Module or upgrade CU firmware.

F30053

Error in FPGA data

Replace the Power Module.

F30662

CU hardware fault

Switch CU off and on again, upgrade firmware, or contact technical

support.

F30664

CU power up aborted

Switch CU off and on again, upgrade firmware, or contact technical

support.

F30850

Software fault in Power Module

Replace Power Module or contact technical support.

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы:

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 298 / 346

Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы: