Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 290

Страница: 290 / 346

Alarms, faults and system messages

9.2 Alarms

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN

288

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

9.2

Alarms

Alarms have the following properties:
●

They do not have a direct effect in the inverter and disappear once the cause has been

removed

●

They do not need have to be acknowledged

●

They are signaled as follows
–

Status display via bit 7 in status word 1 (r0052)

–

at the Operator Panel with a Axxxxx

–

via STARTER, if you click on TAB at the bottom left of the STARTER screen

In order to pinpoint the cause of an alarm, there is a unique alarm code and also a value for

each alarm.

Alarm buffer

For each incoming alarm, the inverter saves the alarm, alarm value and the time that the

alarm was received.

$ODUPFRGH

$ODUPYDOXH

'D\V

)ORDW

'D\V

$ODUPWLPH

UHFHLYHG

$ODUPWLPH

UHPRYHG

$ODUP

U>@

U>@ U>@ U>@ U>@ U>@ U>@

Figure 9-1

Saving the first alarm in the alarm buffer

r2124 and r2134 contain the alarm value - important for diagnostics - as "fixed point" or

"floating point" number.
The alarm times are displayed in r2145 and r2146 (in complete days) as well as in r2123 and

r2125 (in milliseconds referred to the day of the alarm).

The inverter uses an internal time calculation to save the alarm times. More information on

the internal time calculation can be found in Chapter Real time clock (RTC) (Page 247).
As soon as the alarm has been removed, the inverter writes the associated instant in time

into parameters r2125 and r2146. The alarm remains in the alarm buffer even if the alarm

has been removed.
If an additional alarm is received, then this is also saved. The first alarm is still saved. The

alarms that have occurred are counted in p2111.

$ODUPFRGH

$ODUPYDOXH

$ODUPWLPH

UHFHLYHG

$ODUPWLPH

UHPRYHG

$ODUP

U>@

U>@ U>@ U>@ U>@ U>@ U>@

Figure 9-2

Saving the second alarm in the alarm buffer

The alarm buffer can contain up to eight alarms. If an additional alarm is received after the

eighth alarm - and none of the last eight alarms have been removed - then the next to last

alarm is overwritten.

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы:

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 290 / 346

Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы: