manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 119 / 346

Поделиться
Скачать
Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 119

 

Configuring the fieldbus 

 

6.1 Communication via PROFIBUS 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

117

 

Error 

value 1 

Meaning 

15 hex 

Response too long (the length of the actual response exceeds the maximum transfer length) 

16 hex 

Illegal parameter address 

(illegal or unsupported value for attribute, number of elements, parameter number, 

subindex or a combination of these)

 

17 hex 

Illegal format (change request for an illegal or unsupported format) 

18 hex 

Number of values not consistent 

(number of values of the parameter data to not match the number of elements 

in the parameter address)

 

19 hex 

Drive object does not exist (access to a drive object that does not exist) 

6B hex 

No change access for a controller that is enabled. 

6C hex 

Unknown unit. 

6E hex 

Change request is only possible when the motor is being commissioned (p0010 = 3). 

6F hex 

Change request is only possible when the power unit is being commissioned (p0010 = 2). 

70 hex 

Change request is only possible for quick commissioning (basic commissioning) (p0010 = 1). 

71 hex 

Change request is only possible if the converter is ready (p0010 = 0). 

72 hex 

Change request is only possible for a parameter reset (restore to factory setting) (p0010 = 30). 

73 hex 

Change request is only possible when Safety Integrated is being commissioned (p0010 = 95). 

74 hex 

Change request is only possible when a technological application/unit is being commissioned (p0010 = 5). 

75 hex 

Change request is only possible in a commissioning state (p0010 ≠ 0). 

76 hex 

Change request is not possible for internal reasons (p0010 = 29). 

77 hex 

Change request is not possible at download. 

81 hex 

Change request is not possible at download. 

82 hex 

Transfer of the control authority (master) is inhibited by BI: p0806. 

83 hex 

Requested BICO interconnection is not possible (BICO output does not supply a float value, however the BICO 

input requires a float value) 

84 hex 

Converter does not accept a change request (converter is busy with internal calculations, see r3996) 

85 hex 

No access methods defined. 

C8 hex 

Change request below the currently valid limit (change request to a value that lies within the "absolute" limits, 

but is however below the currently valid lower limit) 

C9 hex 

Change request above the currently valid limit (change request to a value that lies within the "absolute" limits, 

but is however above the currently valid upper limit, e.g. specified as a result of the converter power rating) 

CC hex  Change request not permitted (change is not permitted as the access code is not available) 

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Отзывы:

Нет отзывов