manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 76 / 346

Поделиться
Скачать
Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 76

Commissioning 

 

4.5 Commissioning with STARTER 

 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 

74

 

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

4.5.4

 

Making additional settings 

After the basic commissioning, you can adapt the inverter to your application as described in 

the Commissioning (Page 53). 
STARTER offers two options:  
1.

 

Change the settings using the appropriate screen forms - our recommendation.  

①

 Navigation bar: For each inverter function, select the corresponding screen form. 

②

 tabs: Switch between screen forms. 

If you change the settings using screen forms you do not need to know the parameter 

numbers. 

 

2.

 

You change the settings using the parameters in the expert list.  

If you wish to change the settings using the expert list, you need to know the 

corresponding parameter number and its significance. 

Saving settings so that they are not lost when the power fails 

All of the changes that you make are temporarily saved in the inverter and are lost the next 

time the power supply is switched off. For your changes to be permanently saved in the 

inverter, you must save the changes using the   button (RAM to ROM). Before you press 

the button, you need to mark the appropriate drive in the project navigator. 

Go offline 

You can now exit the online connection after the data backup (RAM to ROM) with   

"Disconnect from target system". 

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Отзывы:

Нет отзывов