Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 122 | Manualshive

Страница: 122 / 346

Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 122

Configuring the fieldbus

6.2 Communication via RS485

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN

120

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

6.2.2.2

Basic settings for communication

Parameter

Description

P0015 = 21

Macro drive unit
Selecting the I/O configuration

p2020

Value

4

5

6

7

8

9

10

11

12

13

Baud rate
2400

4800

9600

19200

38400

57600

76800

93750

115200

187500

p2022

Fieldbus interface, USS PZD count
Setting the number of 16-bit words in the PZD part of the USS telegram
Fieldbus interface, USS PKW count
Setting the number of 16-bit words in the PKW part of the USS telegram:

p2023

Value

0

3

4

127

PKW count
PKW 0 words

PKW 3 words

PKW 4 words

PKW variable

p2040

Fieldbus interface, monitoring time [ms]
Setting the monitoring time to monitor the received process data via fieldbus. If no

process data are received within this time, an appropriate message is output

Additional information and parameters are provided on the following pages.

6.2.2.3

Structure of a USS telegram

A USS telegram comprises a sequence of characters, which are sent in a defined sequence.

Every character within the telegram comprises 11 bits. The sequence of characters of a USS

telegram is shown in the following diagram.

6WDUWGHOD\

866IUDPH

n net data

Final

information

Header information

ELWGDWD

%LW

VWRS

%LW

3HYHQ

%LW

6WDUW

STX

LGE

ADR

1.

2.

: : :

n

BCC

Figure 6-5

Structure of a USS telegram

«
...
120
121
122
123
124
...
»

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Отзывы:

Нет отзывов