Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 129

Страница: 129 / 346

Configuring the fieldbus

6.2 Communication via RS485

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

127

Parameter value (PWE)

You can vary the number of PWEs using parameter p2023.

Parameter channel with fixed length

Parameter channel with variable length

P2023 = 4
A parameter channel with fixed length should

contain 4 words as this setting is sufficient for all

parameters (including double words).
P2023 = 3
You can select this setting if you only want to

read or write 16-bit data or alarm signals.

•

16-bit data: e.g. p0210 supply voltage

•

32-bit data:
Indexed parameter, e.g. p0640[0…n]
Bit parameter, e.g. 722.0...12

The master must always transmit the

permanently set number of words in the

parameter channel. Otherwise the slave will not

respond to the telegram.
When the slave responds it must always respond

with the defined number of words.

P2023 = 127
For a variable length of parameter channel, the

master will only send the number of PWEs

necessary for the task in the parameter channel.

The response telegram is also no longer than

necessary.

Note
8-bit values are transmitted as 16-bit values; the higher-order byte is zero. The fields of 8-bit

values require one PWE per index.

Rules for editing requests/responses

●

You can only request one parameter for each telegram sent.

●

Each received telegram contains only one response.

●

The master must repeat a request until it receives a suitable response.

●

Request and response are assigned to one another using the following identifiers:
–

Suitable response identifier

–

Suitable parameter number

–

Suitable parameter index IND, if required

–

Suitable parameter value PWE, if necessary

●

The master must send the complete request in one telegram. Request telegrams cannot

be split up. The same applies to responses.

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы:

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 129 / 346

Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы: