manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 32 / 346

Поделиться
Скачать
Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 32

Installing 

 

3.3 Installing Power Module 

 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 

30

 

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

3.3

 

Installing Power Module 

Installing Power Modules with degree of protection IP20  

 

●

 

Install the Power Module vertically on a mounting plate in a control cabinet. 

The smaller frame sizes of the converter (FSA and FSB) can also be mounted on DIN 

rails using an adapter. 

●

 

When installing, observe the minimum clearances to other components in the control 

cabinet. 

These minimum clearances are necessary to ensure adequate cooling of the converter. 

●

 

Do not cover the ventilation openings the converter. 

Installing additional components 

Depending on the application, additional line reactors, filters, braking resistors, brake relays 

etc., may also be used. 
Please observe the mounting and installation instructions supplied with these components. 

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Отзывы:

Нет отзывов