manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 156 / 346

Поделиться
Скачать
Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 156

Configuring the fieldbus 

 

6.3 Communication over CANopen 

 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 

154

 

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

6.3.2

 

Commissioning CANopen 

6.3.2.1

 

Setting the node ID and baud rate 

In the converter you must set the node ID and the baud rate to permit communication.  

 

CAUTION 

 

Changes made to the node ID or baud rate only become effective after switching off and on 

again. It is particularly important that any external 24 V supply is switched off.  
Note that before turning off, you must save the changes using RAM -> ROM (

). 

The currently active Node ID is displayed in parameter r8621. 

 

Setting the node ID 

You can define the node ID either using the DIP switch on the Control Unit, using parameter 

p8620 or in STARTER in the screen form under "Control Unit/Communication/CAN" under 

the CAN interface tab.  

 

Valid node IDs: 

1 … 126 

Invalid node IDs: 

0, 127 

When a valid node ID has been set using DIP switches, then this is always effective and 

p8620 cannot be changed. 
If you set all DIP switches to "OFF" (0) or "ON" (1), then the Node ID set in p8620 or 

STARTER is effective. 
The positions and settings of the DIP switches are described in Section Interfaces, 

connectors, switches, control terminals, LEDs on the CU (Page 46). 

Setting the data transmission rate 

You can set the transmission rate in the range from 10 kbit/s … 1 Mbit/s using parameter 

p8622 or in the STARTER screen form "Control Unit/Communication/CAN" under the CAN 

interface tab.  

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Отзывы:

Нет отзывов