Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 57

Страница: 57 / 346

Commissioning

4.1 Restoring the factory setting

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

4.1

Restoring the factory setting

There are cases where something goes wrong when commissioning a drive system e.g.:
●

The line voltage was interrupted during commissioning and you were not able to

complete commissioning.

●

You got confused when setting the parameters and you can no longer understand the

individual settings that you made.

●

You don't know whether the inverter was already operational

In cases such as these, reset the inverter to the factory settings.

Restoring the factory setting with STARTER or BOP-2

This function resets the settings in the inverter to the factory settings.

Note
The communication settings and the settings of the motor standard (IEC/NEMA) are retained

even after restoring the factory setting.

Table 4- 1

Procedure

STARTER

BOP-2

Go online with STARTER

In STARTER, click on the button

In the "Options" menu, select the

"DRVRESET" entry

Confirm the reset using the OK key

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы:

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 57 / 346

Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы: