Siemens SINAMICS G120 CU230P-2 Скачать руководство пользователя страница 283

Страница: 283 / 346

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

281

Service and maintenance

8.1

Overview of replacing converter components

In the event of a permanent function fault, you can replace the converter's Power Module or

Control Unit independently of one another. In the following cases, you may immediately

switch on the motor again after the replacement.

Replacing the Power Module

Replacing the Control Unit with external backup of the

settings, e.g. on a memory card

Replacement:

•

Same type

•

Same power rating

Replacement:

•

Same type

•

Higher

power rating

Replacement:

•

Same type

•

Same firmware version

Replacement:

•

Same type

•

higher

firmware version

(e.g. replace FW V4.2 by
FW V4.3)

303

6,1

&8&

303

6,1

&8&

6,1$

0,&

6,1

6,1$

0,&

6,1

303

&8&

6,1

&8&

6,1

6,1$

0,&

6,1

6,1$

0,&

6,1

303

&8&

6,1

&8&

6,1

Power Module and motor

must be adapted to one

another (ratio of motor and

Power Module rated power >

1/8)

The converter automatically loads the settings on the

memory card into the new CU.
If you have saved the settings of your converter on another

medium, e.g. on an operator panel or on a PC, then after

the replacement, the settings must be loaded into the

converter.

WARNING

In all other cases, you must recommission the drive.

Содержание SINAMICS G120 CU230P-2



























































































































































































































































































































































Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы:

Siemens SINAMICS G120 CU230P-2, Руководство по эксплуатации, Страница: 283 / 346

Результаты поиска

Содержание SINAMICS G120 CU230P-2

Отзывы: