the bank (
Bank
) and custom control (
CC
) you
want to cancel
•
CancelAll
— press the
CancelAll
knob to
insert a cancel all custom controls command
Cancel All
— insert a cancel all custom controls
command
•
State
— press the
Insert
knob to insert the state
State
— insert the switcher state
4.
Press the
Insert
knob to insert the event. Click
Insert
to insert the event.
5.
Press
START/STOP
. Click
Stop Recording
.
Running a Custom Control
Once a custom control has been programmed, you can
run that custom control by pressing the button that the
custom control was recorded to.
Keep the following in mind when running custom
controls:
•
A custom control will continue to run until it reaches
a hold event, is stopped by another custom control,
you edit a custom control, or the custom control
reaches the end.
•
When a custom control is running, the button on the
custom control bus is red.
•
When a custom control is held (at a Hold event), the
button on the custom control bus flashes white.
•
You can run multiple custom controls at the same
time. The number of running custom controls is
shown on the display when in custom control mode.
•
You can stop a running custom control by pressing
the red custom control button on the custom control
bank.
•
You can stop all running custom controls by selecting
a custom control with no events recorded to it.
•
A maximum of 128 custom controls can be run at the
same time.
To Run a Custom Control
Once a custom control has been recorded, you can run
that custom control at any time.
1.
Press
MENU
. Click
Navigation Menu
>
Custom
Control
>
Shot Box
.
2.
Select the bank that the custom control you want to
run is on by pressing the bank button.
3.
Select the custom control you want to run by
pressing the source button on the custom control
bus. Click a custom control button to run that
specific custom control.
The custom control starts to play immediately.
Editing a Custom Control
After you have recorded a custom control, you can go
back and edit that custom control to add or remove
events.
Tip:
Custom controls can also be edited from the Custom
Control node in DashBoard.
To Edit a Custom Control
When editing a custom control, you can delete and insert
events at any point in the custom control, or append
events to the end.
Tip:
When editing a custom control, press RUN EVENT to run
the currently selected event. This can help you diagnose
problems in a custom control.
1.
Press
MENU
>
BANK 1
>
EDIT
.
2.
Use the
Bank
knob to select the bank that the
custom control you want to record will be stored on,
or select the bank button directly.
3.
Use the
CC
knob to select the custom control that
you want to edit, or select the custom control on the
bus directly. The custom control will have an
*
next
to the number.
4.
Use the
Func
knob to select where and how you
want to edit the custom control.
•
Edit
— select the position in the custom control
to edit events
•
Append
— add events to the end of the custom
control
5.
Press the
Func
knob to start editing.
Tip:
You can also start editing a custom control by pressing
and holding EDIT and selecting the bank and custom that
you want to edit to.
The display changes to show the name and duration
of the custom control, and the currently selected
event in the custom control.
6.
Delete an event in a custom control as follows:
a)
Use the left knob to select the event you want
to delete. You can also use the
PREV
and
NEXT
buttons.
b)
Press
DELETE
.
7.
Insert an event into a custom control as follows:
a)
Use the left knob to select the event you want
to insert an event before. You can also use the
PREV
and
NEXT
buttons.
b)
Press
INSERT
.
c)
Insert the events you want.
Carbonite Operation Manual (v13.0) — Custom Controls •
61