5.
Use the
M-Inv
knob to invert the masked area with
the unmasked area (
On
). Click
Mask Invert
to
invert the masked area with the unmasked area.
The portion of the key that was masked out is now
visible, and the portion that was visible is masked.
6.
Press
NEXT
.
7.
Use the
X Pos
and
Y Pos
knobs to position the
mask. You can also use the positioner. Use the
X-Position
and
Y-Position
sliders, or drag the
Position
cross-hair, to position the mask.
8.
Use the
Size
knob to adjust the size of the mask
region. You can also twist the positioner. Use the
Size
slider to adjust the size of the mask region.
9.
Press
NEXT
.
10.
Adjust the position of the left and right sides of the
box mask as follows:
a)
Use the
Left/R
knob to adjust the position of
the left side of the box mask.
b)
Press the
Left/R
knob.
c)
Use the
L/Right
knob to adjust the position of
the right side of the box mask.
11.
Use the
Left Edge
and
Right Edge
sliders to
adjust the position of the left and right sides of the
box mask.
12.
Adjust the position of the top and bottom sides of
the box mask as follows:
a)
Use the
Top/B
knob to adjust the position of
the top side of the box mask.
b)
Press the
Top/B
knob.
c)
Use the
T/Bttm
knob to adjust the position of
the bottom side of the box mask.
13.
Use the
Top Edge
and
Bottom Edge
sliders to
adjust the position of the upper and lower sides of
the box mask.
Split Keys
A Split key allows you to assign a different alpha source
for a key than the fill/alpha associations that are set up
during configuration, or to use a separate alpha source
for a Self key.
A split key can be applied to an
AUTO SELECT
, or
SELF KEY
.
To Set Up a Split Key
A split key works on an
Auto Select
or
Self Key
that
has been set up and you want to apply a different alpha
to.
1.
Set up your key with the video source you want to
use.
2.
Press and hold the
Auto Select
or
Self Key
,
depending on the key type you are splitting. Click
Navigation Menu
>
Live Assist
and select the
key you want split.
3.
Press the source button on the key bus for the alpha
source you want to use.
Tip:
If the new alpha source is not assigned to a source
button, press any other button on the key bus and use the
Alpha knob to select a different alpha source.
4.
Click the
Key Fill
or
Key Alpha
button and select
the new source for the key.
•
Key Fill
— select a different source for the key.
This will change the alpha selection as well.
•
Key Alpha
— select a different alpha for the
key. Selecting the different alpha creates the split
key.
Key Copy
You can copy the entire contents of a keyer to another
keyer in the same, or a different ME. The entire contents
of the destination keyer are replaced with the contents
of the source keyer.
When you copy a key, the switcher tries to assign
resources to the destination key to match the source key.
If these resources are not available, the switcher steals
resources in the following order.
1.
From off-air keys that are not the source key.
2.
From the source key, if it is not on-air.
3.
From on-air keys that are not the source key.
4.
From the source key, even if it is on-air.
To Copy a Key
This procedure copies the contents of Key 1 to Key 3 as
an example. Use the same procedure for any key
combination.
1.
Press and hold the
KEY 3 SEL
button.
This is the destination keyer that you want to copy
to.
2.
Press the
KEY 1 SEL
button.
This is the source keyer that you want to copy from.
Key Swap
You can swap the entire contents of any two keyers in
the same, or different MEs. The video source, position,
and key type are all swapped between keyers. This allows
Carbonite Operation Manual (v13.0) — Keying •
45