Perkins 1106C Series Скачать руководство пользователя страница 89

Страница: 89 / 192

KENR6932

Disassembly and Assembly Section

g01337874

Illustration 157
Typical example

Thoroughly clean the mating surface of the front

housing.

If the original front cover is installed, follow Steps

2.a through 2.b.

Thoroughly clean front cover (1).

Install a new joint (2) to front cover (1). Engage

three locators (Y) into the holes in the front

cover.

Install Tooling (A) into holes (X) in the front

housing.

Use Tooling (A) in order to position the front cover

assembly onto the front housing.

Install bolts (3) and (4). Install bolt (5)

nger tight.

Ensure that the different bolts are installed in the

correct positions.

Note:

The bolt (5) may not be installed to some

engines.

Loosely install the water pump assembly and

remove Tooling (A). Refer to Disassembly and

Assembly, “Water Pump - Install” for the correct

procedure.

Tighten bolts (3), (4) and (5) to a torque of 22 N·m

(16 lb ft).

Tighten the bolts for the water pump to a torque of

22 N·m (16 lb ft).

End By:

If the engine has a fan, install the fan. Refer to

Disassembly and Assembly, “Fan - Remove and

Install”.

i02654515

Gear Group (Front) - Remove

and Install

Removal Procedure

Table 38

Required Tools

Tool

Part

Number

Part Name

Qty

21825576

Crankshaft Turning Tool

27610291

Barring Device Housingl

27610289

Gear

27610212

Camshaft Timing Pin

27610286

Crankshaft Timing Pin

27610287

Adapter

Start By:

Remove the front cover. Refer to Disassembly and

Assembly, “Front Cover - Remove and Install”.

Remove the valve mechanism cover. Refer to

Disassembly and Assembly, “Valve Mechanism

Cover - Remove and Install”.

NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened

component life.

NOTICE

Care must be taken to ensure that

uids are contained

during performance of inspection, maintenance, test-

ing, adjusting and repair of the product. Be prepared to

collect the

uid with suitable containers before open-

ing any compartment or disassembling any compo-

nent containing

uids.

Dispose of all

uids according to local regulations and

mandates.

Содержание 1106C Series

































































































































































































Результаты поиска

Содержание 1106C Series

Отзывы:

Perkins 1106C Series, Разборка и сборка, Страница: 89 / 192

Результаты поиска

Содержание 1106C Series

Отзывы: