Perkins 1106C Series Скачать руководство пользователя страница 82

Страница: 82 / 192

KENR6932

Disassembly and Assembly Section

g01337603

Illustration 144

Typical example

If the engine has an aluminum oil pan, remove

dust seal (6).

g01337605

Illustration 145

Typical example

Remove joint (7).

If necessary, remove dowels (5) from the cylinder

block.

Remove oil seal (8) from

ywheel housing (1).

Installation Procedure (Wet Back
End Housing)

Table 30

Required Tools

Tool

Part

Number

Part Description

Qty

Guide Stud
(M10 by 100 mm)

1861117

POWERPART

Universal Jointing Compound

NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened

component life.

Ensure that the

ywheel housing is clean and free

from damage. If necessary, replace the

ywheel

housing.

g01337605

Illustration 146

Typical example

Install a new oil seal (8) to

ywheel housing (1).

Note:

Press the oil seal into the

ywheel housing

from the rear. Ensure that the front edge of the oil seal

ush with the joint face of the

ywheel housing .

Inspect crankshaft rear seal (9) for leaks. If there

are any oil leaks, replace the crankshaft rear seal.

Refer to Disassembly and Assembly, “Crankshaft

Rear Seal - Remove” and refer to Disassembly

and Assembly, “Crankshaft Rear Seal - Install”.

Содержание 1106C Series

































































































































































































Результаты поиска

Содержание 1106C Series

Отзывы:

Perkins 1106C Series, Разборка и сборка, Страница: 82 / 192

Результаты поиска

Содержание 1106C Series

Отзывы: