manualshive.com logo in svg

Perkins 1106C Series, Разборка и сборка, Страница: 101 / 192

Поделиться
Скачать
Perkins 1106C Series Скачать руководство пользователя страница 101

KENR6932

101

Disassembly and Assembly Section

g01338003

Illustration 194

13.

Tighten bolts (7), (8) and (9) in the sequence that

is shown in illustration 194 to a torque of 28 N·m

(20 lb ft).

Note:

Ensure that the housing and the cylinder block

are correctly aligned.

14.

Remove Tooling (C) from the cylinder block.

15.

If necessary, install a new crankshaft front seal.

Refer to Disassembly and Assembly, “Crankshaft

Front Seal - Remove and Install”.

g01337982

Illustration 195
Typical example

16.

Install new O-ring seals (4) and (5) to bypass tube

(1). Use Tooling (E) in order to lubricate the O-ring

seals. Install bypass tube (2) to the cylinder head.

Install bolts (1). Tighten the bolts to a torque of

22 N·m (16 lb ft).

End By:

a.

Install the fuel injection pump. Refer to

Disassembly and Assembly, “Fuel Injection Pump

- Install”.

b.

Install the timing gears. Refer to Disassembly and

Assembly, “Gear Group (Front) - Install”.

c.

If the engine has an accessory drive, install

the accessory drive. Refer to Disassembly and

Assembly, “Accessory Drive - Remove and

Install”.

d.

Install the engine oil pan. Refer to Disassembly

and Assembly, “Engine Oil Pan - Install”.

e.

Install the front pulley. Refer to Disassembly and

Assembly, “Vibration Damper and Pulley - Install”.

f.

If necessary, install the alternator. Refer to

Disassembly and Assembly, “Alternator - Install”.

g.

Install the fan. Refer to Disassembly and

Assembly, “Fan - Remove and Install”.

h.

Fill the cooling system with coolant. Refer to

Operation and Maintenance Manual, “Cooling

System Coolant - Fill” for the correct procedure.

i02654444

Accessory Drive - Remove and

Install

 

Removal Procedure

NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened

component life.

Содержание 1106C Series

































































































































































































Отзывы:

Нет отзывов