Perkins 1106C Series Скачать руководство пользователя страница 33

Страница: 33 / 192

KENR6932

Disassembly and Assembly Section

g01341874

Illustration 57

Typical calibration code

If a replacement electronic unit injector is installed,

the correct injector trim

le must be programmed

into the electronic control module. Refer to

Troubleshooting, “Injector Trim File” for more

information. The code that is required to obtain

the injector trim

le is located at position (X).

Note:

Record code (X) before the electronic unit

injector is installed.

Use Tooling (D) to remove any fuel from the

cylinder.

Note:

Evacuate as much fuel as possible from the

cylinder before installing the electronic unit injector.

Ensure that the fuel inlet port of the electronic unit

injector is capped. Ensure that the electronic unit

injector is clean.

g01255701

Illustration 58

On installing an original electronic unit injector,

install a new O-ring seal (15) and sealing washer

(14) to electronic unit injector (11).

Ensure that the O-ring seal (15) and sealing

washer (14) on a new electronic unit injector are

not damaged and in place.

Note:

Do not lubricate the O-ring seal.

Ensure that the seat for the electronic unit injector

in the cylinder head is clean and free from

damage. Ensure that the sealing washer has been

removed from the cylinder head.

g01255699

Illustration 59

Install clamp (13) to electronic unit injector (11).

Install the electronic unit injector assembly into the

original location in the cylinder head.

Note:

Ensure that the electronic unit injector is

pushed

rmly against the seat in the cylinder head.

Install the electronic unit injector for number one

cylinder

rst. Install the electronic unit injectors in

numerical order.

Install a new torx screw (12) to clamp (13). Tighten

the torx screw

nger tight.

Remove the cap from electronic unit injector (11).

Install a new seal (8) to electronic unit injector (11)

and to the valve mechanism cover base. Ensure

that the

ange on the seal is

ush with the valve

mechanism cover base.

Remove the plugs from the new fuel injection

line. Loosely install the fuel injection line. Refer to

Disassembly and Assembly, “Fuel Injecton Lines -

Install”.

Note:

Ensure that the ends of the fuel injection line

are seated in the electronic unit injector and the fuel

manifold. Tighten the nuts

nger tight.

Содержание 1106C Series

































































































































































































Результаты поиска

Содержание 1106C Series

Отзывы:

Perkins 1106C Series, Разборка и сборка, Страница: 33 / 192

Результаты поиска

Содержание 1106C Series

Отзывы: