manualshive.com logo in svg

Perkins 1106C Series, Разборка и сборка, Страница: 24 / 192

Поделиться
Скачать
Perkins 1106C Series Скачать руководство пользователя страница 24

24

KENR6932

Disassembly and Assembly Section

g01335384

Illustration 35
Alignment of timing marks

5.

Mark gears (1), (2) and (3) in order to show

alignment. Refer to Illustration 35.

Note:

Identi

fi

cation will ensure that the gears can be

installed in the original alignment.

6.

Loosen nut (8) for fuel pump gear (3).

7.

Install Tooling (D) through three holes in fuel pump

gear (3). Tighten Tooling (D) until fuel pump gear

(3) is released.

8.

Remove Tooling (D) from fuel pump gear (3).

9.

Remove nut (8) and the washer from fuel pump

gear (3). Remove the fuel pump gear.

i02654507

Fuel Injection Pump Gear -

Install

 

Installation Procedure

Table 6

Required Tools

Tool

Part Number

Part Name

Qty

B

27610212

Camshaft Timing Pin

1

27610286

Crankshaft Timing Pin

1

C

27610287

Adapter

1

NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened

component life.

Note:

The fuel injection pump must remain locked

until the procedure instructs you to unlock the fuel

injection pump.

1.

Ensure that number one piston is at top dead

center on the compression stroke. Refer to

System Operation, Testing and Adjusting, “Finding

Top Center for No. 1 Piston”.

g01335380

Illustration 36

2.

Ensure that Tooling (C) is installed in hole (Y) in

the cylinder block. Use Tooling (C) in order to lock

the crankshaft in the correct position.

g01335394

Illustration 37

3.

Ensure that Tooling (B) is installed into hole (X) in

camshaft gear (1).

4.

Ensure that shaft (9) of the fuel injection pump is

clean and free from damage.

5.

Ensure that the fuel injection pump is locked in

the correct position. Refer to Disassembly and

Assembly, “Fuel Injection Pump - Install”.

6.

Ensure that the fuel pump gear is clean and free

from wear of damage. If necessary, replace the

fuel pump gear.

Содержание 1106C Series

































































































































































































Отзывы:

Нет отзывов